Perform the following steps:
- Setting the Base UDP Port Value
- Configuring the Intra-cluster VNFC Interface
- Configuring Load Balancing Service for the Cluster
- Configuring the D-SBC Signaling Port or DFE Port for the Cluster
- Configuring the DNS Group for the Cluster
| Anchor |
|---|
| Setting the Base Udp Port value |
|---|
| Setting the Base Udp Port value |
|---|
|
Setting the Base UDP Port Value
| Info |
|---|
|
To use packet IP interface's UDP port higher than 1023, it is required to set baseUdpPort parameter. The loadBalancingService intra-cluster communication uses UDP port 3057. |
To set the value of the parameter baseUdpPort to more than 3057, execute the following command:
| Code Block |
|---|
set system media mediaPortRange baseUdpPort 3060
commit |
| Anchor |
|---|
| Configuring the Intra-cluster VNFC Interface |
|---|
| Configuring the Intra-cluster VNFC Interface |
|---|
|
Configuring the Intra-cluster VNFC Interface
To Configure the packet interface for intra-cluster VNFC communication by setting the parameter type to type, execute the following commands:
IPv6 address:
| Code Block |
|---|
set system clusterAdmin clusterComm type ip addressContext default ipInterfaceGroup LIG2 pktIpVar IF3.IPV6
commit |
IPv4 address:
| Code Block |
|---|
set system clusterAdmin clusterComm type ip addressContext default ipInterfaceGroup LIG2 pktIpVar IF3.IPV4
commit |
To Configure the management interface for intra-cluster VNFC communication by setting the parameter type to mgmt, execute the following commands:
IPv6 address:
| Code Block |
|---|
set system clusterAdmin clusterComm type mgmt addressContext default ipInterfaceGroup LIG2 mgmtIpVar IF0.IPV6
commit |
IPv4 address:
| Code Block |
|---|
set system clusterAdmin clusterComm type mgmt addressContext default ipInterfaceGroup LIG2 mgmtIpVar IF0.IPV4
commit |
| Info |
|---|
|
You must configure Cluster Admin before configuring D-SBC Signaling Port, Load Balancing Service, and DNS Group parameters for intra-cluster VNFC communication. |
| Anchor |
|---|
| Configuring Load Balancing Service for the Cluster |
|---|
| Configuring Load Balancing Service for the Cluster |
|---|
|
Configuring Load Balancing Service for the Cluster
To Configuring the parameter loadBalancingService for the Cluster, execute the following command:
| Code Block |
|---|
set system loadBalancingService groupName mCCluster.dsbcUser01.com
set system loadBalancingService privateIpInterfaceGroupName LIG2
commit |
| Anchor |
|---|
| Configuring the D-SBC Signaling Port or DFE Port for the Cluster |
|---|
| Configuring the D-SBC Signaling Port or DFE Port for the Cluster |
|---|
|
Configuring the D-SBC Signaling Port or DFE Port for the Cluster
To configure the parameter dsbcSigPort or DFE port for the cluster, execute the following command:
| Code Block |
|---|
set system dsbc dsbcSigPort ipInterfaceGroup LIG2 ipVarV4 IF3.IPV4 state enabled mode inService
commit |
| Anchor |
|---|
| Configuring the DNS Group for the Cluster |
|---|
| Configuring the DNS Group for the Cluster |
|---|
|
Configuring the DNS Group for the Cluster
To configure the parameter dnsGroup for the cluster, execute the following command:
| Code Block |
|---|
set addressContext default dnsGroup test type mgmt interface mgmtGroup server test ipAddress 10.7.6.40 state enabled
commit |