Versions Compared

Old Version 6

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH2pmohanUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca67042e, userName='null'}
AUTH1sbsarkarUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c, userName='null'}
REV5dalvesUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccd208db, userName='null'}
REV6radaikalamUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c7cd0042, userName='null'}
REV3vbsinghUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cef20cc2, userName='null'}
REV1challaskUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c9f10380, userName='null'}

Panel

In this section:

Table of Contents
maxLevel3

Info
iconfalse

Related articles:

Children Display

 

Include Page
Transparency_Profile_Note
Transparency_Profile_Note

This section specifies the Privacy parameters for Egress Ip Attributes.

To View and Edit Privacy

On SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Ip Signaling Profile > Egress Ip Attributes > Privacy. The Privacy window is displayed.

DEFAULT_H323

On the Privacy window, choose the Ip Signaling Profile as DEFAULT_H323 to view the Privacy parameters for H323 Trunk Group.

Caption
0Figure
1Trunk Provisioning - Egress Ip Attributes H323 Privacy
 

There are no Privacy parameters for DEFAULT_H323 type of Egress Ip Attributes.

DEFAULT_SIP

Scenario 1: Transparency is disabled

On the Privacy window, choose the Ip Signaling Profile as DEFAULT_SIP to view the Privacy parameters for SIP Trunk Group.

Caption
0Figure
1Trunk Provisioning - Egress Ip Attributes SIP Privacy
 

The following fields are displayed:

Caption
0Table
1Egress Ip Attributes SIP Privacy Parameters
 

Parameter

Description

Transparency

Enable flag to allow ingress Privacy information to pass through unchanged.

  • Disable (default)
  • Enable
Privacy Information

NOTE: This parameter is visible only when the Transparency parameter is set to Disable.

Use this object to specify which of the following headers the SBC uses when sending privacy information in outgoing SIP INVITE messages:

  • P Asserted Id – Used among trusted SIP entities (typically intermediaries) to carry the identity of the caller as it was verified by authentication.
  • P Preferred Id – Used by a User Agent (UA) to carry the identity the caller wishes to be used, and sent to a trusted proxy to be inserted in the P-Asserted-Identity field.
  • Remote Party Id – Used among trusted SIP entities (typically intermediaries) to carry the identity of the caller as it was verified by authentication. This header is specified in an earlier RFC that continues to be supported.

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

Scenario 2: Transparency is enabled

When the Transparency flag is set to Enable. The appearance of the Edit Privacy window changes, and the Anonymize Host IP Portion flag appears.

Caption
0Figure
1Edit Privacy - Anonymize Host IP Portion

 

Note

By default, the flags Transparency and Anonymize Host IP Address are set to Disable for the Egress IP Attributes of all IP Signaling Profiles.

 

The flag Anonymize Host IP Portion is described in the table below:

ParameterDescription
Anonymize Host IP Portion

When the flag is set to enable, the SBC anonymizes the incoming host IP portion of the private headers (P-AID, P-PID, RPID) by replacing it with the IP address of the SBC, before sending it to the egress leg of a call.

To activate this feature, set the flag Anonymize Host Ip Portion to enable.

  • Disable (default)
  • Enable


To enhance privacy transparency, set the Anonymize Host IP Portion flag to Enable.

To save the changes, click Save. To cancel all changes made since the last saved state, click Undo Edits.

Note
  • Anonymization of the host IP address is currently supported only for in-dialog messages, and not out-of-dialog messages.
  • Anonymization of the host IP address is supported for the following message types:
    • INVITE
    • BYE
    • OPTIONS
    • SUBSCRIBE
    • NOTIFY
    • UPDATE
    • PUBLISH
    • MESSAGE

 

Pagebreak