Use this object to configure H323 Signaling Port for this zone.
| Note |
|---|
Each signaling port within an Address Context must use a unique IP address. |
| Include Page |
|---|
| Unique_IP_for_SigPort |
|---|
| Unique_IP_for_SigPort |
|---|
|
| Include Page |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
|
To View H323Sig Port
On SBC main screen, go to Configuration > System Provisioning > Category: Base Provisioning > Signaling Ports > H323Sig Port. The H323Sig Port window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Signaling Ports - H323Sig Port |
|---|
|
|
The H323Sig Port can be checked for each Address Context or for each Zone or for all the Address Contexts and Zones created. Use the drop-down box to select the desired Address Context and Zone.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | H323Sig Port Main Field |
|---|
|
|
To Edit H323Sig Port
To edit any of the H323Sig Ports in the list, click the radio button next to the specific H323Sig Port name.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | H323Sig Port Highlighted |
|---|
|
|
The Edit Selected H323Sig Port window is displayed below.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | H323Sig Port Edit Window |
|---|
|
|
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
To Create H323Sig Port
To create a new H323Sig Port, click New H323Sig Port tab on the H323Sig Port List panel.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | H323Sig Port Fields |
|---|
|
|
The Create New H323Sig Port window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | H323Sig Port Create Window |
|---|
|
|
The following fields are displayed:
| Caption |
|---|
|
Parameter | Description |
|---|
Index
| Specify the index value. | IP Interface Group Name
| The name of the IP interface group used by this Signaling Port. | H225Ip Address
| The 32-bit IP address used for H225 signaling. Specified in dotted decimal form (for example 128.127.50.224). Default is 0.0.0.0. | Port Number
| The logical port number of the UDP port to use for this connection. This defines the H.225 well known port. Must be 1-5000, default is 1720. | H245Ip Address
| The 32-bit IP address used for H245 signaling. Specified in dotted decimal form (for example 128.127.50.224). Default is 0.0.0.0. This must equal ipaddress1 in the current implementation. | Mode
| The operational state of the H323 signaling service: inService—the signaling port listens for incoming H323 signal link connection requests.outOfService—the signaling port is not available for incoming H323 signal link connection requests and thus cannot be used to create a new gateway signal links to other H323 gateways.
| State
| The administrative state of this H323 signaling port: disabled—Not active.enabled—Active
| Action
| The method by which active calls using this H323 signaling service are processed when MODE goes to out of service: dryup—all calls are allowed to complete until TIMEOUT expires.force—all calls are dropped immediately.
| Dry Up Timeout
| The time (in minutes) to wait for active calls to finish in order to place the H323 signaling service in out of service MODE. Must be 0-1440, default is 0. | DSCP Value
| Differentiated Services Code Point value (0-63). |
|
To Delete H323Sig Port
To delete any of the created H323Sig Port, click the radio button next to the specific H323Sig Port which you want to delete.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | H323Sig Port Highlighted |
|---|
|
|
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | H323Sig Port Delete Confirmation |
|---|
|
|
Click Yes to remove the specific H323Sig Port from the list.