Page History

Add_workflow_for_techpubs

AUTH1
REV5
REV6
REV3
REV1

Panel

In this section:

Table of Contents

maxLevel	3

Include Page

	Call_Stats_Terms
	Call_Stats_Terms

Excerpt Include

	Resource Monitoring and Statistics
	Resource Monitoring and Statistics
nopanel	true

Include Page

	IntervalStatsMustMatchEMS
	IntervalStatsMustMatchEMS

System

Command Syntax

The command syntax of the objects related to the show table systemcommand is shown below.

Code Block

language	none

show table system
	activeConfigFile
	admin
	announcements
	baseMacAddress
	clusterAdmin
	congestion
	coredumpList
	coredumpSummary
	cpuUtilCurrentStatistics
	cpuUtilIntervalStatistics
	databaseIntegrity
	daughterBoardAdmin 
	daughterBoardStatus
	dodModeStatus
	dsbc
	dspPad
	dspRes
	dspStatus
	ethernetPort
	fanStatus
	fileStatisticsAdmin
	fileStatisticsStatus
	fipsFSMState
	fipsBypassMode
	haConfig
	hardDiskStatus
	hardDiskUsage
	highAvailabilityPort
	intervalStatistics
	ipPolicing
	jsrcServer
	ledStatus
	licenseFeatureStatus
	licenseInfo
	licenseLegacyBundleInfo
	licenseLocalBundleInfo
	licenseMode
	licenseRequired
	licenseServer
	licenseServerStatus
	licenseStatus
	loadBalancingService
	logicalMgmtIpInterface
	logicalMgmtIpInterfaceStatus
	macAddressStatus
	media
	mediaProfile
	memoryUtilCurrentStatistics
	memoryUtilIntervalStatistics
	metavariable
	mgmtIpInterfaceGroup
	mgmtStaticRoute
	networkProcessorStatistics
	ntp
	objectStoreParameters
	pathCheckPath
	policyServer
	powerSupplyStatus
	rgStatus
	savedConfigList
	sbcPersonalityStatus
	security
	serverAdmin
	serverSoftwareUpgradeStatus
	serverStatus
	softwareUpgradeDetailedStatus
	softwareUpgradeStatus
	standbySyncStatus
	syncStatus
	systemCongestionCurrentStatistics
	systemCongestionIntervalStatistics
	systemCongestionStatus

Command Parameters

Multiexcerpt

MultiExcerptName	Shared Parameters

Caption

0	Table
1	Shared Common Parameters - 'show status system' and 'show table system'
3	Shared Parameters

The Sonus System Congestion Interval Statistics details.

<sequence number> – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.

avgCallRate – The system average call arrival rate over the reporting inteval (callArrivals / interval-time = avgCallRate).

avgRegRate – The average SIP registration arrival rate (in registrations per second) over the reporting interval.

avgSubsRate – The average SIP SUBSCRIBE arrival rate (in subscriptions per second) over the reporting interval.

callArrivals – The total count of call arrivals during the interval (callArrivals / interval-time = avgCallRate) .

emergencyCallArrivals – The total count of SIP emergency calls that arrived.

emergencyCallRejects – The total count of rejected SIP emergency calls.

intervalValid– A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.

levelMC1Count – The total count of transitions into MC1 during the interval.

levelMC1TotalTime – The total time spent (in seconds) in MC1 during the interval.

levelMC2Count – The total count of transitions into MC2 during the interval.

levelMC2TotalTime – The total time spent (in seconds) in MC2 during the interval.

levelMC3Count – The total count of transitions into MC3 during the interval.

levelMC3TotalTime – The total time spent (in seconds) in MC3 during the interval.

maxActiveCalls – The high water mark of the total number of active calls in both inbound and outbound directions on all trunk groups in the system for specified interval. This statistic applies to calls which are setting up, tearing down or stable.

Switch-over scenario:

When a switch-over occurs from SBC-A to SBC-B, the number of stable calls that were transferred from SBC-A to SBC-B equals the initial value of "maxActiveCalls" (immediately after the switch-over). Subsequent values are calculated and recorded accordingly.

overloadRejects – The total count of calls rejected during the collection interval.
peakCallRate – The system peak call arrival rate (in calls per second) measured during the collection interval.
peakRegRate – The peak SIP registration arrival rate (in registrations per second) measured during the collection interval.
peakSubsRate – The peak SIP SUBSCRIBE arrival rate (in sbuscriptions per second) measured during the collection interval.
sipRegArrivals – The total count of SIP registrations that arrived during the collection interval.
sipRegRejects – The total count of SIP registrations rejected during the collection interval.
sipSubsArrivals – The total count of SIP SUBSCRIBEs that arrived during the collection interval.
sipsSubsRejects – The number of SIP SUBSCRIBEs rejected during the collection interval.
time – The system up time when the interval statisitic is collected.

Parameter

Description

activeConfigFile Displays the file name of the last retrieved file from the external object store service.

admin

Basic configuration (name, location, etc) for the system. See Admin Attributes table below for details.

announcements

Announcement file status and statistics. See Announcements Attributes table below for details.

baseMacAddress

Displays base MAC address of servers.

activeBaseAddress – The base MAC address assigned to the active server.
assignedBaseAddress – The base MAC address assigned to this server.

clusterAdmin

Displays cluster-specific configuration details.

mgmtInterfaceGroup – The Management Interface Group used for intra-cluster communication
mgmtIpAddress – The management IP address used for intra-cluster communication
type – The interface type used during intra-cluster communication

congestion

System congestion profile for the node.

adaptive – adaptive overload configuration.
levelMC1 – Configuration for congestion level MC1.
levelMC2 – Configuration for congestion level MC2.
levelMC3 – Configuration for congestion level MC3.
mode – Mode (static or adaptive) of the system overload control.
policer – System congestion Call Rate Policer configuration.

coredumpList

List of core dumps on the server(s). Fields include:

coredumpFileName
size
dateAndTime
newSinceLastStart (true/false)

coredumpSummary

Summary of core dump files on server(s).

<server name> – The name of the server.
coredumpAndTraceCount – Number of coredumps and trace files.
totalSize – Indicates the total size of the coredumps (KBytes).

cpuUtilCurrentStatistics

The CPU utilization of the server for the current period.

<server name> – The name of the server.
average – The average CPU % utilization for this interval.
high – The high CPU % utilization for this interval.
low – The low CPU % utilization for this interval.

cpuUtilIntervalStatistics

The CPU utilization for the 'n' number of intervals.

number – The interval sequence number. The number of intervals to store are configurable. (Refer to Interval Statistics - CLI for status/statistics details)
ceName – The SBC server name.
cpu – The CPU number.
intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
time – The system up time when the interval statistics are collected.
average – The average CPU % utilization for this interval.
high – The high CPU % utilization for this interval.
low – The low CPU % utilization for this interval.

databaseIntegrity

Displays SBC database sync status from executing the request system admin <system name> verifyDatabaseIntegrity command. (Refer to Admin - CLI)

The following command options are available to match the results of the 'show' command with the associated 'request' command:

activeAndStandbyPolicy – Display results of the sync check against policy databases on the active and standby servers.
activeConfigAndActivePolicy – Displays the results of the sync check against the policy and configuration databases on the active server.

Displayed results include the following fields:

syncModuleName – The database sync module name: activeAndStandbyPolicy, activeConfigAndActivePolicy
syncStatus – Possible results: inProgress, inSync, outOfSync, unknown.
timeStamp – Times tamp of when the command was executed.

daughterBoardAdmin

SBC 5x10/7000 daughter board administrative status from server/CE level.

ceName – The SBC server name.
disableCleanupAction – Identifies the type of disable cleanup action (forced/graceful)
dryUpTime – The set time, in minutes, for a graceful shutdown to occur (range: 0-60 / default = 10).
slot – Slot number designation for DSP20 (slot 1) and DSP25 (slots 1-4) cards.
state – Administrative state of daughter board.

NOTE: Not applicable for 5x00 or SWe systems.

daughterBoardStatus

Server Daughter Board (DB) status details. See Daughter Board Status Attributes table below for details.

dodModeStatus

DoD mode status details, with following details:

index – Index number
status – Specifies if DoD mode is enabled/disabled, as well as if CLI, EMA Platform Mode and sFTP are enabled for access while SBC is in DoD mode.

dsbc

D-SBC statistics details.

dsbcSigPortStatistics – D-SBC Signaling Port statistics when communicating with the other D-SBC nodes. Fields include:
- <IP address> – The IP address of the remote node
- BytesReceived – The total number of signaling bytes received from this remote node
- BytesSent – The total number of signaling bytes sent to this remote node
- Interface – The interface used for this link
- PdusReceived – The total number of signaling PDUS received from the remote node
- PdusSent – The total number of signaling PDUS sent to the remote node
- State – The current state of the signaling link of the remote node
dsbcSigPortStatus – D-SBC Signaling Port status details.
- <index> – The D-SBC Signaling Port index.
- state – The administrative state of the D-SBC Signaling Port.

dspPad

DSP PAD configuration service (must be restarted for new configuration to take effect). See DSP PAD Attributes table for details (for 'show table system' command only).

dspRes

DSP historical interval statistics. See DSP Resources Attributes table below for parameter details.

dspCallCurrentStatistics – The Sonus System Call DSP Resource Current table.
dspCallIntervalStatistics – The Sonus System Call DSP Resource Interval table.
dspUsageCurrentStatistics – The Sonus DSP Resource Current table.
dspUsageIntervalStatistics – The Sonus DSP Resource Interval table.

dspStatus dspUsage

Status of DSP resources. See DSP Status Attributes table below for details.

ethernetPort

Configuration for management, packet, and field service Ethernet ports. See Ethernet Port Attributes table for details.

fanStatus

Fan status on the server(s).

<system name>
<fan nomenclature>
speed

fileStatisticsAdmin

Displays whether the following interval statistics are enabled/disabled to write data to the statistics file.

CallFailIntervalStats
CallIntervalStats
DiamNodeRfIntervalStatistics
DnsGroupDnsServerStats
DspResDspCallIntervalStats
DspResDspUsageIntervalStats
H323SigPortStatisticsStats
IpAclOverallStats
IpAclRuleStats
IpPolicingSystemIntStats
LinkDetectionGroupStats
LinkMonitorStats
MtrmConnPortPeerStats
NBS5200TrunkGroupStatusStatsNOTE: This statistic applies to both SBC 5000 and 7000 series. The EMS uses "SBC7KTrunkGroupStatusStats" for SBC 7000 series statistics.
SipIntervalStats
sipOcsCallIntervalStatistics
SipRegCountStats
SipSigPortStatisticsStats
SipSubCountStats
SysCpuUtilIntStatsSts
SysMemoryUtilIntStatsSts
SystemCongestionIntervalStats
TrafficControlStats
ZoneIntervalStatisticsStats

fileStatisticsStatus

Displays the current ID of the last performance statistics data written to the database.fipsBypassMode

Displays FIPS bypass mode (alternating bypass or exclusive crypto).

fipsFSMState

FIPS finite state machine state.

issuer – FIPS FSM Issuer.
message – FIPS FSM message.
state – FIPS FSM state.
timeStamp – FIPS FSM timestamp.

haConfig

This statistic displays GRHA status details.

serverName
leaderElection – The current GRHA mode setting for the leader election algorithm type.
bondMonitoring – The current GRHA mode setting for bond monitoring type.

hardDiskStatus

Hard disk status on the server(s).

capacity – Capacity of the disk.
diskLifeRemaining – A calculated percentage estimating the life remaining of the device or N/A if not supported by the device.
diskStatus – Hard disk status that indicates if the disk is online/failed.
healthTest – Pass or Fail indicating the overall health of the device.
present – Indicates if the hard disk exists (true/false).
productId – Product ID of the hard disk as assigned by vendor.
revision – Revision of the hard disk as assigned by vendor .

hardDiskUsage

Hard disk usage on the server(s).

freeDiskSpace – Indicates free hard disk space (KBytes).
role – Role of the server for the indicated partition (see Note below).
syncCompletion – Indicates partition's sync completion percentage.
syncStatus – Partition's synchronization status with peer server.
totalDiskSpace – Capacity of the disk (KBytes).
usedDiskSpace – Indicates used hard disk (%) .

NOTE: The role of the standby server is reflected as Primary for the root partition because the other partition, /var/log/sonus/sbx/evlog is not mirrored/mounted in the standby CE until a switch-over occurs and the Standby assumes the role of active.

highAvailabilityPort

Configuration and status for the HA ethernet ports.

statistics – Lists status/statistics details such as port name, number of packets transmitted/received, bytes transmitted/received, and errors transmitted/received.
- <host name> – SBC host name.
- allocRxBufFailRx – The number of receive buffer allocation errors.
- byteRx – The number of bytes received.
- byteTx – The number of bytes transmitted.
- crcErrRx – The number of receive CRC errors.
- errTx – The number of transmit errors.
- noBufCntRx – The number of receive no buffer errors.
- overErrRx – The number of receive overrun errors.
- packetRx – The number of packets received.
- packetTx – The number of packets transmitted.
status – List details such as port name, MAC address, IP address, negotiated speed and OOS reason.
- ipAddress – The IP address of this port.
- macAddress – The MAC address of this port.
- negotiatedSpeed – The negotiated speed of this port.
- oosReason – The reason this port is out of service.

intervalStatistics

The system- wide settings for interval statistics.

maxFileRetentionPeriod – The maximum retention period for statistics files stored on disk. (range: 60-1440 / default = 60)
nodeId – The EMS configured nodeID for this system to be used as part of the filename when writing the statistics to the file. (default = 0)
numOfPastIntervals – The maximum number of past intervals display in CLI. (range: 1-12 / default = 4)
timeInterval – The time interval for interval statistics data.

ipPolicing

The MIB Module for IP Monitoring statistics. These statistics are divided into three categories: Offenders Lists statistics, Micro Flow statistics and System statistics.

Role – Offenders list role
Index – Index number of this statistic
Address Context – Address context associated with this statistic
Interface Group Name – IP interface group name
Interface Name – Interface name
Source IP Address – Source IP address
Destination IP Address – Destination IP address
Source IP Port (1, 2, 4, 7, 8, 9) – Source IP port
Destination IP Port (1, 2, 4, 7, 8, 9) – Destination IP port
IP Protocol – IP protocol
Ether Type (4, 7, 8) – This field indicates the decimal value representing which protocol is encapsulated in the payload of the Ethernet Frame. For example, a value of 2048 equates to 0800 hexidecimal, which in turn represents IPv4.
Discard Count – The number of packets dropped
Ring Type (8)
Source Unique (7, 8)

Offenders Lists statistics (See Offenders List Details section for additional details)

aclOffendersList – The table of statistics for the ACL policer offenders list
aggregateOffendersList – The table of statistics for the aggregate policer offenders list
arpOffendersList – The table of statistics for the ARP policer offenders list
badEtherIpHdrOffendersList – The table of statistics for the bad Ethernet/IP Header policer offenders list
discardRuleOffendersList – The table of statistics for the discard rule offenders list
ipSecDecryptOffendersList – The table of statistics for the IPSEC Decrypt policer offenders list
mediaOffendersList – The table of statistics for the media policer offenders list
rogueMediaOffendersList – The table of statistics for the rogue media policer offenders list
uFlowOffendersList – The table of statistics for the micro flow policer offenders list

Micro Flow statistics:

uFlowStats – The table of micro flow statistics. See IP Policing uFlowStats Fields for details

NOTE: This command displays any microflow entry regardless of whether SIPFE or MRM (or any sub-system) created the microflow.

System statistics:

systemCurStats – The Sonus System Policer Current table. See IP Policing System Current and Interval Attributes table below for a list of attributes.
systemIntStats – The Sonus System Policer Interval table. See IP Policing System Current and Interval Attributes table below for a list of attributes.

Hide

Check this statement which was present in previous releases. Need to determine if it is needed, and what it means.

The following fields display for the above statistics. A field applies to all statistics above unless one or more numbers are shown to indicate the specific statistics applicable.

jsrcServer

JSRC server configuration.

globalConfig – This defines global configuration applicable to all the JSRC servers.
remoteServer – JSRC server configuration.
serverStatus – JSRC server status.

ledStatus

Displays status of various LEDs of the server.

ledColor – Indicates the LED color.
ledState – Indicates the LED state.

licenseFeatureStatus

Status details about each licensed feature. See License Attributes table for details.

licenseInfo

The license status for registered license features. See License Attributes table for details.

licenseLegacyBundleInfo

License details for the legacy licenses stored on the

Spacevars

0	product

. See License Attributes table for details.

licenseLocalBundleInfo

License details for the local licenses stored on the

Spacevars

0	product

. See License Attributes table for details.

licenseMode

The licensing mode of the

Spacevars

0	product

application (legacy, local, or network). See License Attributes table for details.

(Applies to 'show table' command only)

licenseRequired

Displays the licenseRequired configuration: The configured minimum and maximum number of licenses for a particular feature to request from the Site License Server (SLS) for the SBC application to use. See License Attributes table for details.

(Applies to 'show table' command only)

licenseServer

Per-server license configuration. See License Attributes table for details.

(Applies to 'show table' command only)

licenseServerStatus

License server status details. See License Attributes table for details.

licenseStatus

The CE license status table describes the current CE license state, for example "dualCe". See License Attributes table for details.

loadBalancingService

The Load Balancing Service status/statistics details with the following fields. See one of the following tables, as applicable, for details:

logicalMgmtIpInterface

The logical management IP interface status/statistics details with following fields:

name – The name of the logical IP interface.
mgmtIpInterfaceGroupName
ipAddress
state

logicalMgmtIpInterfaceStatus

The Logical Mgmt IP Interface status status/statistics details with following fields:

name – The name of the logical IP interface.
operStatus – Operational status.

macAddressStatus

Displays MAC addresses of the system server(s).

<server name> – SBC server name.
status – Status of the specified MAC address.
usedBy – Name of the server using this MAC address.
usedByPort – The port used by this MAC address.

media

System- wide media configurations, UDP port range and RTP/RTCP peer inactivity timeout.

mediaPeerInactivity – media peer inactivity configurables.
mediaPortRange – Allowed range of UDP port numbers for RTP/RTCP media.
mediaRtcpControl – RTCP session configurables.

mediaProfile

DSP Media Profile configuration.

compression – Percentage (of DSP cores) for capability COMPRESSION.
tone – Percentage (of DSP cores) for capability TONE.

memoryUtilCurrentStatistics

The memory utilization for the current interval period. Fields include:

ceName – The SBC server name.
average – The average memory % utilization for this interval.
averageSwap – The average swap % memory utilization for this interval.
high – The high memory % utilization for this interval.
highSwap – The high swap % memory utilization for this interval.
low – The low memory % utilization for this interval.
lowSwap – The low swap memory % utilization for this interval.

memoryUtilIntervalStatistics

The memory utilization for the 'n' number of intervals.

number – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for status/statistics details.
ceName – The SBC server name.
average – The average memory % utilization for this interval.
averageSwap – The average swap memory % utilization for this interval.
high – The high memory % utilization for this interval.
highSwap – The high swap memory % utilization for this interval.
intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
low – The low memory % utilization for this interval.
lowSwap – The low swap memory % utilization for this interval.
time – The system up time when the interval statistic is collected.

metaVariable

Displays the system dynamic metavariable names and values.

ceName – Displays the name of the instance along with HA IP address.
name – Displays the name of the interface definition parameters.
value – Displays the value associated with the IDP.

mgmtIpInterfaceGroup

A group of management IP interfaces for the default address context.

<mgmt group name>
mgmtIpInterface – The management IP interfaces in this management IP interface group.
- ceName – The name of the SBC server used by this management IP interface.
- ipAddressV4 – The IPV4 Address of the Interface
- ipAddressV6 – The IPV6 Address of the Interface
- portName – The port number used by this IP interface.
- prefixV4 – The IPV4 subnet prefix of this Interface.
- prefixV6 – The IPV6 subnet prefix of this Interface.
- state – Administrative state of the interface.
mgmtIpInterfaceStatus – The status of the IP interfaces in this IP interface group.
- ifindex – The interface index of the management interface.
- operStatus – The actual status of the management interface (disabled, enabledPortDown, enabledPortUp, interfaceCreated, interfaceCreating, resourceAllocated, resourceAllocating).
- rxPackets – Number of packets received on this management interface.
- txPackets – Number of packets sent on this management interface.

mgmtStaticRoute

Static IP routes for this address context.

<destination IP address>
preference – Route preference value.

networkProcessorStatistics

NOTE: For internal debug use only.

Network Processor statistics details.See Network Processor StatisticsAttributes table below for full details.

ntp

NTP Services Management.

peerStatus – This table contains status information about each NTP peer. Fields include:
- ceName – The name of this SBC server.
- ipAddress – IP address of the CE.
- state – the state of the NTP peer (insynce, outofsync, reachable).
- stratum – A number representing the distance from the reference clock, starting at "0". Stratum 16 represents that a device is out of sync.
- refTime – The time this NTP peer was last updated.
serverAdmin – This table contains information about each NTP Server configured to provide network time. Fields include:
- ipAddress – The IP address of this NTP Server.
- version – The NTP version of this NTP Server.
- minPoll – The minimum poll interval to this NTP Server.
- maxPoll – The maxiimum poll interval to this NTP Server.
- state – The configured state of the NTP server entry.
systemStatus – This table contains system status information about NTP. Fields include:
- ceName – The name of this SBC server.
- clock – The SBC regularly checks system time. This field respresents the system time as of the last check by SBC, not the actual system time.
- refTime – The time this system was last updated.
timeZone – This table contains Time Zone configuration. Fields include:
- name – System name.
- zone – The current time zone.

NOTE: In an HA configuration, the Active and Standby system times and refTimes will not match in the results of this command because SBC updates NTP data independently.

policyServer

Softswitch servers and client services status/statistics details. See Policy Server Attributes table below for details.

powerSupplyStatus

Power consumption/state of the server.

<server name>
partNum – Identifies the part number of the module.
powerFault – Indicates if there is power fault.
present – Indicates if the module is present or not.
productName – Identifies the name (as given by manufacturer) of power supply module.
serialNum – Identifies the serial number of the power supply module.
voltageFault – Indicates if there is voltage fault.

rgStatus

Displays the Redundancy Group status of the instances created through N:1 redundancy group.

NOTE: This command applies to N:1 redundancy configurations only.

savedConfigList

List of configurations saved on the system.

<index of saved config. file>
fileName – The file name of the saved configuration.
size – Indicates size of the saved configuration file (KBytes).
version – The software version name of the saved configuration.

sbcPersonalityStatus

Displays the personality role of the

Spacevars

0	product2

/

Spacevars

0	product3

instance. Choices are isbc, msbc and ssbc.

security

Security management status/statistics details. See Security Attributes table for details.

serverAdmin

The serverAdmn table describes the configuration of each server module.

<server name>
coredumpProfile – The core dump settings for this server.
modularType – Hardware modular type of the server.
role – When set to ‘primary’, role designates a server for internal processing.

serverSoftwareUpgradeStatus

The system server software upgrade status table describes the status of the server software upgrade module.

<server name>
upgradeStatus – Indicates the current status of the server (none, pendingRevert, pendingUpgrade, reverted, reverting, revertingOnError, upgraded, upgrading)

serverStatus

The system server status table provides status of the server module.

<server name>
applicationUpTime – Indicates application uptime on the server in days/hours/minutes/sec.
applicationVersion – Indicates the application version currently running on server.
daughterBoardPresent – Daughter board presence indicator.
hwType – Type of server module the indexed slot has been configured to accept.
lastRestartReason – Reason for last restart of server.
mgmtRedundancyRole – Redundancy role of the server (for management entities)
partNum – Identifies the part number of the module.
platformVersion – Platform version currently running on server.
serialNum – Serial number of the server module.
syncStatus – Inter–CE data synchronization state.
upTime – Server module uptime in days/hours/minutes/seconds .

softwareUpgradeDetailedStatus

<system name> detailedStatus – Prints the complete Live Software Upgrade (LSWU) upgrade details for the specified system to the screen. Details include the number of steps involved, the time taken to completed LSWU and upgrade process results.

softwareUpgradeStatus

LSWU status at any given time with the following details.

activeCeAtStart – Active CE name when the upgrade started.
cemodeAtStart – CE mode when upgrade started (single/dual).
modelChange – Indicates if process model changed as part of this upgrade.
newRelease – Software release to which the upgrade is performed.
oldRelease – Software release running before upgrade started.
package – Name of the new package.
previousState – This is the previous LSWU state.
primaryUpgradeStatus – Indicates the current status of the primary server.
reason – Exit reason for failure of last software upgrade.
revertScript – Revert script to run in case upgrade fails.
revertStartTime – Start time of revert activity.
rpmName – Name of the new rpm used for upgrade.
secondaryUpgradeStatus – Indicates the current status of the secondary server.
state – Current LSWU state.
upgradeScript – Script to run to perform upgrade.
upgradeStartTime – LSWU start time.

standbySyncStatus

Sync status details of the standby node for active nodes created through a N:1 redundancy group configuration.

Call/Registration Data – The sync state of Call/Registration data for active or standby node.
Metavar Data – The sync state of metavariable data for the active or standby node.

syncStatus

HA Redundancy:

Sync status of both the active and standby nodes for an SBC HA pair.

Call/Registration Data – Call/Registration data synchronization status with the SBC peer
Configuration Data – Configuration data synchronization status with the SBC peer
Disk Mirroring – Disk Mirroring synchronization status with the SBC peer
Policy Data – Policy data synchronization status with the SBC peer

N:1 Redundancy:

Sync status of both the active and standby nodes created through a N:1 redundancy group.

Call/REgistration Data – The sync state of Call/Registration data for active or standby node.
Metavar Data – The sync state of metavariable data for the active or standby node.

services management details. See NTP Attributes table below for details

objectStoreParameters

Parameters used to specify an object store service to upload or download a configuration file (

Spacevars

0	product3

only)

pathCheckPath

Path for ICMP ping mechanism

name
sourceIpAddress
targetIpAddress
reportSignalIpAddress
reportSignalIpPort
pathCheckProfile
addressContext
zone
ipInterfaceGroup
ipInterface
state

policyServer

Softswitch servers and client services status/statistics details. See Policy Server Attributes table below for details.

powerSupplyStatus

Power consumption/state of the server.

<server name>
partNum – Identifies the part number of the module.
powerFault – Indicates if there is power fault.
present – Indicates if the module is present or not.
productName – Identifies the name (as given by manufacturer) of power supply module.
serialNum – Identifies the serial number of the power supply module.
voltageFault – Indicates if there is voltage fault.

rgStatus

Displays the Redundancy Group status of the instances created through N:1 redundancy group.

NOTE: This command applies to N:1 redundancy configurations only.

savedConfigList

List of configurations saved on the system.

<index of saved config. file>
fileName – The file name of the saved configuration.
size – Indicates size of the saved configuration file (KBytes).
version – The software version name of the saved configuration.

sbcPersonalityStatus

Displays the personality role of the

Spacevars

0	product2

/

Spacevars

0	product3

instance. Choices are isbc, msbc and ssbc.

security

Security management status/statistics details. See Security Attributes table for details.

serverAdmin

The serverAdmn table describes the configuration of each server module.

<server name>
coredumpProfile – The core dump settings for this server.
modularType – Hardware modular type of the server.
role – When set to ‘primary’, role designates a server for internal processing.

serverSoftwareUpgradeStatus

The system server software upgrade status table describes the status of the server software upgrade module.

<server name>
upgradeStatus – Indicates the current status of the server (none, pendingRevert, pendingUpgrade, reverted, reverting, revertingOnError, upgraded, upgrading)

serverStatus

The system server status table provides status of the server module.

<server name>
applicationUpTime – Indicates application uptime on the server in days/hours/minutes/sec.
applicationVersion – Indicates the application version currently running on server.
daughterBoardPresent – Daughter board presence indicator.
hwType – Type of server module the indexed slot has been configured to accept.
lastRestartReason – Reason for last restart of server.
mgmtRedundancyRole – Redundancy role of the server (for management entities)
partNum – Identifies the part number of the module.
platformVersion – Platform version currently running on server.
serialNum – Serial number of the server module.
syncStatus – Inter–CE data synchronization state.
upTime – Server module uptime in days/hours/minutes/seconds .

softwareUpgradeDetailedStatus

<system name> detailedStatus – Prints the complete Live Software Upgrade (LSWU) upgrade details for the specified system to the screen. Details include the number of steps involved, the time taken to completed LSWU and upgrade process results.

softwareUpgradeStatus

LSWU status at any given time with the following details.

activeCeAtStart – Active CE name when the upgrade started.
cemodeAtStart – CE mode when upgrade started (single/dual).
modelChange – Indicates if process model changed as part of this upgrade.
newRelease – Software release to which the upgrade is performed.
oldRelease – Software release running before upgrade started.
package – Name of the new package.
previousState – This is the previous LSWU state.
primaryUpgradeStatus – Indicates the current status of the primary server.
reason – Exit reason for failure of last software upgrade.
revertScript – Revert script to run in case upgrade fails.
revertStartTime – Start time of revert activity.
rpmName – Name of the new rpm used for upgrade.
secondaryUpgradeStatus – Indicates the current status of the secondary server.
state – Current LSWU state.
upgradeScript – Script to run to perform upgrade.
upgradeStartTime – LSWU start time.

standbySyncStatus

Sync status details of the standby node for active nodes created through a N:1 redundancy group configuration.

Call/Registration Data – The sync state of Call/Registration data for active or standby node.
Metavar Data – The sync state of metavariable data for the active or standby node.

syncStatus

HA Redundancy:

Sync status of both the active and standby nodes for an SBC HA pair.

Call/Registration Data – Call/Registration data synchronization status with the SBC peer
Configuration Data – Configuration data synchronization status with the SBC peer
Disk Mirroring – Disk Mirroring synchronization status with the SBC peer
Policy Data – Policy data synchronization status with the SBC peer

N:1 Redundancy:

Sync status of both the active and standby nodes created through a N:1 redundancy group.

Call/REgistration Data – The sync state of Call/Registration data for active or standby node.
Metavar Data – The sync state of metavariable data for the active or standby node.

systemCongestionCurrentStatistics

The Sonus System Congestion Current Statistics table details.

avgCallRate – The average call rate calculated using the formula: (# call attempts in an interval) / (# seconds elapsed in that interval).
avgRegRate – The average registration rate calculated using the formula: (# registration attempts in an interval) / (# seconds elapsed in that interval).
avgSubsRate – The average SIP SUBSCRIBE arrival rate calculated using the formula: (# SUBSCRIBE attempts in an interval) / (# seconds elapsed in that interval).
callArrivals – The number of call arrivals since the current interval started.
emergencyCallArrivals – The number of SIP emergency call arrivals since the current interval started.
emergencyCallRejects – The number of SIP emergency call rejects since the current interval started.
levelMC1Count – The number of transitions into MC1 since the current interval started.
levelMC1TotalTime – The total number of seconds spent in MC1 since the current interval started.
levelMC2Count – The number of transitions into MC2 since the current interval started.
levelMC2TotalTime – The total number of seconds spent in MC2 since the current interval started.
levelMC3Count – The number of transitions into MC3 since the current interval started.
levelMC3TotalTime – The total number of seconds spent in MC3 since the current interval started.
overloadRejects – The number of calls rejected due to system congestion since the current interval started.
peakCallRate – The system peak call arrival rate (in calls per second) since the current interval started.
peakRegRate – The peak SIP registration arrival rate (in registrations per second) since the current interval started.
peakSubsRate – The peak SIP SUBSCRIBE arrival rate (in subscriptions per second) since the current interval started.
sipRegArrivals – The number of SIP registrations arrivals since the current interval started.
sipRegRejects – The number of SIP registrations rejected since the current interval started.
sipSubsArrivals – The number of SIP SUBSCRIBEs that arrived since the current interval started.
sipsSubsRejects – The number of SIP SUBSCRIBEs that are rejected due to system congestion since the current interval started.

systemCongestionIntervalStatistics

The Sonus System Congestion Interval Statistics details.

<sequence number> – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.
avgCallRate – The system average call arrival rate over the reporting inteval (callArrivals / interval-time = avgCallRate).
avgRegRate – The average SIP registration arrival rate (in registrations per second) over the reporting interval

systemCongestionCurrentStatistics

The Sonus System Congestion Current Statistics table details.

avgCallRate – The average call rate calculated using the formula: (# call attempts in an interval) / (# seconds elapsed in that interval).
avgRegRate – The average registration rate calculated using the formula: (# registration attempts in an interval) / (# seconds elapsed in that interval).
avgSubsRate – The average SIP SUBSCRIBE arrival rate calculated using the formula: (# SUBSCRIBE attempts in an interval) / (# seconds elapsed in that interval)in subscriptions per second) over the reporting interval.
callArrivals – The number total count of call arrivals since the current interval startedduring the interval (callArrivals / interval-time = avgCallRate) .
emergencyCallArrivals – The number total count of SIP emergency call arrivals since the current interval startedcalls that arrived.
emergencyCallRejects – The number total count of SIP emergency call rejects since the current interval startedrejected SIP emergency calls.
intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
levelMC1Count – The number total count of transitions into MC1 since during the current interval started.
levelMC1TotalTime – The total number of seconds spent time spent (in seconds) in MC1 since during the current interval started.
levelMC2Count – The number The total count of transitions into MC2 since during the current interval started.
levelMC2TotalTime – The total number of seconds spent time spent (in seconds) in MC2 since during the current interval started.
levelMC3Count – The number The total count of transitions into MC3 since during the current interval started.
levelMC3TotalTime – The total number of seconds spent time spent (in seconds) in MC3 since during the current interval started.overloadRejects
maxActiveCalls – The high water mark of the total number of calls rejected due to system congestion since the current interval started.
peakCallRate – The system peak call arrival rate (in calls per second) since the current interval started.
peakRegRate – The peak SIP registration arrival rate (in registrations per second) since the current interval started.
peakSubsRate – The peak SIP SUBSCRIBE arrival rate (in subscriptions per second) since the current interval started.
sipRegArrivals – The number of SIP registrations arrivals since the current interval started.
sipRegRejects – The number of SIP registrations rejected since the current interval started.
sipSubsArrivals – The number of SIP SUBSCRIBEs that arrived since the current interval started.
sipsSubsRejects – The number of SIP SUBSCRIBEs that are rejected due to system congestion since the current interval started.

systemCongestionIntervalStatistics

systemCongestionStatus

System Congestion status status/statistics details.

systemCongestionCPULevel– The current System Machine Congestion (MC) Level at the time this command is executed.
- 0 – No Congestion
- 1 – Level one congestion
- 2 – Level two congestion
- 3 – Level three congestion
systemCongestionCallAcceptCount – A snapshot of the number of calls being accepted by the system. A value of "65535" represents all calls. During MC2 congestion, SBC calculates the CallAcceptRate peridocially (each second), and uses the value to compute a new CallAcceptCount.
systemCongestionCallAcceptRate – Current rate (in calls per second) at which calls are being accepted by the system.
systemCongestionCallArrivalRate – A snapshot of the number of call arrivals in the last second.
systemCongestionCallEqArrivalRate – A snapshot of the number of call arrivals and registrations in the last second .
systemCongestionCallRateLevel – Call rate congestion level.
systemCongestionIRTTLevel – Internal RoundTrip Time (IRTT) congestion level.
systemCongestionMCDuration – Number of seconds the system has been at this congestion level.
systemCongestionMCLevel – System congestion level.
systemCongestionRegArrivalRate – A snapshot of the number of SIP registration arrivals in the last second.
systemCongestionSubsArrivalRate – The number of SIP SUBSCRIBEs that arrived in the last second.

Admin

active calls in both inbound and outbound directions on all trunk groups in the system for specified interval. This statistic applies to calls which are setting up, tearing down or stable.

Switch-over scenario:
When a switch-over occurs from SBC-A to SBC-B, the number of stable calls that were transferred from SBC-A to SBC-B equals the initial value of "maxActiveCalls" (immediately after the switch-over). Subsequent values are calculated and recorded accordingly.

overloadRejects – The total count of calls rejected during the collection interval.
peakCallRate – The system peak call arrival rate (in calls per second) measured during the collection interval.
peakRegRate – The peak SIP registration arrival rate (in registrations per second) measured during the collection interval.
peakSubsRate – The peak SIP SUBSCRIBE arrival rate (in subscriptions per second) measured during the collection interval.
sipRegArrivals – The total count of SIP registrations that arrived during the collection interval.
sipRegRejects – The total count of SIP registrations rejected during the collection interval.
sipSubsArrivals – The total count of SIP SUBSCRIBEs that arrived during the collection interval.
sipsSubsRejects – The number of SIP SUBSCRIBEs rejected during the collection interval.
time – The system up time when the interval statisitic is collected.

systemCongestionStatus

System Congestion status status/statistics details.

systemCongestionCPULevel – The current System Machine Congestion (MC) Level at the time this command is executed.
- 0 – No Congestion
- 1 – Level one congestion
- 2 – Level two congestion
- 3 – Level three congestion
systemCongestionCallAcceptCount – A snapshot of the number of calls being accepted by the system. A value of "65535" represents all calls. During MC2 congestion, SBC calculates the CallAcceptRate peridocially (each second), and uses the value to compute a new CallAcceptCount.
systemCongestionCallAcceptRate – Current rate (in calls per second) at which calls are being accepted by the system.
systemCongestionCallArrivalRate – A snapshot of the number of call arrivals in the last second.
systemCongestionCallEqArrivalRate – A snapshot of the number of call arrivals and registrations in the last second .
systemCongestionCallRateLevel – Call rate congestion level.
systemCongestionIRTTLevel – Internal RoundTrip Time (IRTT) congestion level.
systemCongestionMCDuration – Number of seconds the system has been at this congestion level.
systemCongestionMCLevel – System congestion level.
systemCongestionRegArrivalRate – A snapshot of the number of SIP registration arrivals in the last second.
systemCongestionSubsArrivalRate – The number of SIP SUBSCRIBEs that arrived in the last second.

Admin

Command Syntax

Code Block
> show table system admin

Command Parameters

Caption

0	Table
1	Admin Attributes
3	Admin Attributes

Parameter	Description
`<system name>`	System name
`accountManagement`	Account and password management-related configuration
`actualSystemName`	System name given by the user as user/metadata
`auditLogState`	Management audit log state
`banner`	The configurable banner text that displays when users login to EMA and CLI applications. Refer to Banner - CLI for configuration details.
`cliSetWarningSupport`	Setting to enable/disable warning prompts configured for the set command.
`clusterId`	clusterID instance present in the userdata
`contact`	Contact information of the system
`dod`	DOD-related configuration
`dspMismatchAction`	Action to take for one of the following DSP mismatch conditions: Mismatch in DSP card installation across any/all slot locations. Cards must match by slot location. For any mismatched slot, DSP capacity is not used when “preserveRedundancy” is configured (and card dried up if calls were already in place when the mismatch occurred), or if left unprotected when “preserveCapacity” is configured. Mismatch in DSP card type within a slot location. Card installations must match by type – DSP25 (higher capacity) or DSP20 (lower capacity). Same rules as above apply.
`externalAuthenticationEnabled`	The Conf-D CLI user information stored on remote Radius server for authentication
`fips-140-2`	FIPS-140-2 related configuration and commands
`localAuthenticationEnabled`	The Conf-D CLI user information stored locally for authentication
`location`	Physical location of the system.
`passwordDictionary`	Password management dictionary related configuration
`passwordRules`	The rules implementing Conf-D user password policy
`passwordRulesForAdmin`	The rules implementing user password policy for Administrator users
`preserveCapacity`	The Active continues to use the extra DSP capacity, as needed, assuming appropriate session licenses are in place; partial redundancy is in effect NOTE: If a switchover occurs, calls using the extra, non-matching DSP capacity on Active are not protected during switchover (i.e. partial redundancy)
`preserveRedundancy`	The Active automatically triggers a graceful dry-up in an attempt to align DSP hardware capabilities. Once dry-up completes, the Active uses the protected, matching DSP capacity to preserve redundancy. NOTE: During the dry-up period, active calls using the extra, non-matching DSP capacity are not protected in the event that a switchover occurs before the dry up completes.
`rest`	REST API flag setting
`sftpUserPassword`	Password rules for SFTP user
`sshPublicKeyAuthorizationEnabled`	The current state of this flag which is used for SSH public key authentication through CLI for all users
`utilMonitorStatsInterval`	The time interval for system resource monitoring statistics.
`utilMonitorStatsNumOfPastInterval`	The number of past intervals saved for system resource monitoring statistics.

Announcements
Announcement file status and statistics.
Command Syntax
Code Block
> show table system announcements

Command Parameters
Multiexcerpt
MultiExcerptName Announcements
Caption
0 Table
1 Announcements Attributes
3 Announcements Attributes
Parameter Description
memoryUsage
Announcement segment NP memory usage.
cachedSegments – Number of announcement segments cached in NP memory.
totalCacheMemory – Total amount of segment cache memory available in NP.
totalPlayoutTime – Total playout time of all segments cached in NP memory.
totalSegments – Total number of announcement segments on disk.
usedCacheMemory – Amount of segment cache memory being used in NP.
utilizedCacheMemory – Percentage of segment cache memory being used in NP.
segmentStatus <segment ID>
Announcement segment file status.
audioFormat – Compression type of audio data.
audioLength — Length of audio data in segment file.
pathname – Pathname of segment file.
playoutDuration – Playout duration of segment file.
state – State of segment.
totalPlays – Total number of times this segment has been played.
useCount – Number of announcements currently using this segment.
version – Version number of segment file.

Daughter Board Status
Server Daughter Board (DB) status details.
Info
Applies to SBC 5xxx and SBC 7000 only.
Command Syntax
Code Block
> show table system daughterBoardStatus

Command Parameters
Multiexcerpt
MultiExcerptName Daughter Board
Caption
0 Table
1 Daughter Board Status Attributes
3 Daughter Board Status Attributes
Parameter Description
daughterBoardStatus <server name> – Server name
daughterBoardId
Daughter board identifier
SBC 5000 series:
SPS100 – SBC 5x00 SPS100 module
DB0 – SBC 5x00 SPS100DB 0 module
DB1 – SBC 5x00 SPS100DB 1 module
DSP20 – SBC 5x10 DSP20 module
DSP25 – SBC 5x10 DSP25 module
SBC 7000 series:
FRU_DSP1 – SBC 7000 DSP-LC slot 1
FRU_DSP2 – SBC 7000 DSP-LC slot 2
FRU_DSP3 – SBC 7000 DSP-LC slot 3
FRU_DSP4 – SBC 7000 DSP-LC slot 4
fpgaVersion
A card’s programmed firmware version (using FPGA build date)
NOTE: This maintenance field does not apply to SPS100 cards.
imageLoadFailureCount
Number of module boot failures since the last successful module boot, for use during diagnostic testing of a potentially failed module.
NOTE: This maintenance field does not apply to SPS100 cards.
operationalStatus
Operational state of daughter board.
disabled – Card is disabled.
dryup – Card is enabled but in the process of drying up. Once completed, card will be set to ‘disabled’.
enabled – Card is enabled.
failed – If a DSP2x or DSP-LC module fails to boot over three consecutive tries (typically due to a hardware failure), it is taken out of service and marked as state “failed”. The rest of the system continues to boot normally, including any other DSP modules. The module failure is logged/alarmed with trap “sonusConnexIpSystemCESlotFailedNotification”. The slot remains in the failed state until the module is disabled and re-enabled once a replacement card is installed.
loading – Card is enabled but in the process of booting. Resources are not yet available. Once completed, card will be set to ‘enabled’.
locked – Slot capacity is locked out due to mismatch (with “preserveRedundancy” configured).
NOTE: For 5x00 systems, only the “enabled” state displays in the results.
partNum The part number of the module (if present)
present Indicates if the module is present or not.
productName Identifies manufacturer name of module (if present)
serialNum
Identifies the serial number of the module (if present)
Anchor
DSP Attributes
DSP Attributes
DSP
DSP PAD
DSP PAD configuration service (SBC must be restarted for new configuration to take effect).
Command Syntax
Code Block
> show table system dspPad
Command Parameters
Caption
0 Table
1 DSP PAD Attributes
3 DSP PAD Attributes
Parameter Description
audioTxDuring2833
State of Audio Transmit During 2833.
comfortEnergy
Initial estimate (in –dBm) to be used for generating comfort noise.
jitterEvalPeriod
Time period to decide when to periodically evaluate playout occupancy (in milliseconds).
jitterMinOccThsh
If occupancy falls below this threshold for some time period we advance the playout time (in milliseconds).
playoutTimeseriesPeriod
Duration of one period of the RTP playout buffer loss time series statistic.
playoutTimeseriesThreshold0
Threshold #0 for generation of the playout loss time series statistic.
playoutTimeseriesThreshold1
Threshold #1 for generation of the playout loss time series statistic.
playoutTimeseriesThreshold2
Threshold #2 for generation of the playout loss time series statistic.
rtpDtmfRelay
RTP Payload type to be received as DTMF relay during compressed calls.
sidHangoverTime
Minimum time (in milliseconds) after DSP detects speaker going inactive before sending silence packets.
sidMaxNoiseFloor
Maximum noise floor (in –dBm).
sidMaxTime
Maximum time (in milliseconds) between silence packets.
sidMinNoiseFloor
Minimum noise floor (in –dBm).
sidMinTime
Minimum time (in milliseconds) between silence packets.
toneThreshold
Percentage Threshold crossing value for tone resources.
toneThresholdState
State of Tone Threshold Event.
universalCompressionThreshold
Percentage Threshold crossing value for Universal Compression resources.
universalCompressionThresholdState
State of Universal Compression Threshold Event.

DSP Resources
Command Syntax
Code Block
> show table system dspRes dspCallCurrentStatistics dspCallIntervalStatistics dspUsageCurrentStatistics dspUsageIntervalStatistics

Command Parameters
system dspPad
Command Parameters
Caption
0 Table
1 DSP PAD Attributes
3 DSP PAD Attributes
Parameter Description
audioTxDuring2833
State of Audio Transmit During 2833.
comfortEnergy
Initial estimate (in –dBm) to be used for generating comfort noise.
jitterEvalPeriod
Time period to decide when to periodically evaluate playout occupancy (in milliseconds).
jitterMinOccThsh
If occupancy falls below this threshold for some time period we advance the playout time (in milliseconds).
playoutTimeseriesPeriod
Duration of one period of the RTP playout buffer loss time series statistic.
playoutTimeseriesThreshold0
Threshold #0 for generation of the playout loss time series statistic.
playoutTimeseriesThreshold1
Threshold #1 for generation of the playout loss time series statistic.
playoutTimeseriesThreshold2
Threshold #2 for generation of the playout loss time series statistic.
rtpDtmfRelay
RTP Payload type to be received as DTMF relay during compressed calls.
sidHangoverTime
Minimum time (in milliseconds) after DSP detects speaker going inactive before sending silence packets.
sidMaxNoiseFloor
Maximum noise floor (in –dBm).
sidMaxTime
Maximum time (in milliseconds) between silence packets.
sidMinNoiseFloor
Minimum noise floor (in –dBm).
sidMinTime
Minimum time (in milliseconds) between silence packets.
toneThreshold
Percentage Threshold crossing value for tone resources.
toneThresholdState
State of Tone Threshold Event.
universalCompressionThreshold
Percentage Threshold crossing value for Universal Compression resources.
universalCompressionThresholdState
State of Universal Compression Threshold Event.

DSP Resources
Command Syntax
Code Block
> show table system dspRes dspCallCurrentStatistics dspCallIntervalStatistics dspUsageCurrentStatistics dspUsageIntervalStatistics

Command Parameters
Multiexcerpt
MultiExcerptName DSP Resource
Caption
0 Table
1 DSP Resources Attributes
3 DSP Resources Attributes
Parameter Description
dspRes
<system name or sequence number>
The system name (for CurrentStatistics objects).
A sequence number which identifies the interval for which the set of statistics is required (for IntervalStatistics objects).
dspCallCurrentStatistics
The Sonus System Call DSP Resource Current table containing the following information:
The following statistics are collected in this table for each codec.
numCallSuccessNoDspAllocFailure – Number of successful calls without DSP resource allocation failure during the current time interval.
numCallSuccessWithDspAllocFailure – Number of successful calls with DSP resource allocation failure during the current time interval.
numCallFailNo<codec> – Number of calls failed due to lack of DSP resource for the specified codec since initialization/last reboot.
numCallFailOtherOn<codec> – Number of call fails due to reason other than lack DSP resources for the specified codec since initialization/last reboot.
numCallSuccessNo<codec> – Number of successful calls even though lack of DSP resourcesfor the specified codec since initialization/last reboot.
dspCallIntervalStatistics
The Sonus System Call DSP Resource Interval table containing the following statistics for the 'n' number of intervals:
number – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.
intervalValid– A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
time – The system up time when the interval statisitics are collected
Multiexcerpt
MultiExcerptName DSP Resource
Caption
0 Table
1 DSP Resources Attributes
3 DSP Resources Attributes
initialization/last reboot
numCallSuccessNo<codec> – Number of successful calls even though lack of DSP resourcesfor the specified codec since initialization/last reboot.
The Sonus System Call for : the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
time – The system up time when the interval statisitics are collected.
numCallSuccessNoDspAllocFailure – Number of successful calls without DSP resource allocation failure for the defined time interval.
numCallSuccessWithDspAllocFailure – Number of successful calls with DSP resource allocation failure for the defined time interval.
numCallFailNo<codec> – Number of failed calls due to lack of DSP resource for the specified codec during the defined time interval.
numCallSuccessNo<codec> – Number of successful calls even though lack of AMRNB DSP resource for the specified time interval.
Parameter Description
dspRes
<system name or sequence number>
The system name (for CurrentStatistics objects).
A sequence number which identifies the interval for which the set of statistics is required (for IntervalStatistics objects).
dspCallCurrentStatistics
The Sonus System Call DSP Resource Current table containing the following information:
The following statistics are collected in this table for each codec
.
numCallSuccessNoDspAllocFailure – Number of successful calls without DSP resource allocation failure during for the current defined time interval.
numCallSuccessWithDspAllocFailure – Number of successful calls with DSP resource allocation failure during for the current defined time interval.
numCallFailNo<codec> – Number of failed calls failed due to lack of DSP resource for the specified codec since initialization/last rebootduring the defined time interval.numCallFailOtherOn<codec>
numCallSuccessNo<codec> – Number of call fails due to reason other than lack DSP successful calls even though lack of AMRNB DSP resource for the specified time interval.
dspUsageCurrentStatistics
The Sonus DSP Resource statistics details.
The following statistics are collected in this table for each codec. Statistics are collected once per second.
<codec>AverageAvailCount – The running average number of free DSP resources for the specified codec since
the SBC started up.
<codec>AverageUsedCount – The running average number of used DSP resources for the specified codec since the SBC started up.
<codec>PeakUsedCount – The peak number of resources used for the specified codec since the SBC started up.
dspUsageIntervalStatistics
The Sonus
dspCallIntervalStatistics
DSP Resource Interval table containing the following statistics
over the 'n' number of intervals
. Interval statistics are weighted per codec type.
number – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.
intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than
dspUsageCurrentStatistics
The Sonus DSP Resource statistics details.
The following statistics are collected in this table for each codec. Statistics are collected once per second.
<codec>AverageAvailCount – The running average number of free DSP resources for the specified codec since the SBC started up.
<codec>AverageUsedCount – The running average number of used DSP resources for the specified codec since the SBC started up.
<codec>PeakUsedCount – The peak number of resources used for the specified codec since the SBC started up.
dspUsageIntervalStatistics
The Sonus DSP Resource Interval table containing the following statistics over the 'n' number of intervals. Interval statistics are weighted per codec type.
number – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.
intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
time – The system up time when the interval statisitics are collected.
<codec>AverageAvailCount – The running average number of free DSP resources for the specified codec over the defined interval.
<codec>AverageUsedCount – The running average number of used DSP resources for the specified codec over the defined interval.
<codec>PeakUsedCount – The peak number of resources used for the specified codec over the defined interval.
NOTE: The number of available transcoded calls depends on whether or not back-to-back transcoding is required. Also, DSP resources are commonly held during call setup (even when transcoding ultimately is not required on the call). At a high call rate this can marginally cut into the number of DSP resources available on the system.

DSP Status
Command Syntax
Code Block
> show table system dspStatus

Command Parameters
the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
time – The system up time when the interval statisitics are collected.
<codec>AverageAvailCount – The running average number of free DSP resources for the specified codec over the defined interval.
<codec>AverageUsedCount – The running average number of used DSP resources for the specified codec over the defined interval.
<codec>PeakUsedCount – The peak number of resources used for the specified codec over the defined interval.
NOTE: The number of available transcoded calls depends on whether or not back-to-back transcoding is required. Also, DSP resources are commonly held during call setup (even when transcoding ultimately is not required on the call). At a high call rate this can marginally cut into the number of DSP resources available on the system.

DSP Status
This statistic command provides the current number of transcoded sessions per DSP2x slot (
Spacevars
0 product
5x10) or SPS100 module (SBC 5x00) depending upon the number of modules installed for the specified system. The
Spacevars
0 product
5x10 can include up to four DSP modules. The
Spacevars
0 product
5x00 can be configured for up to three SPS100 modules
(Refer to Customer Replaceable Units for details).
Command Syntax
Code Block
> show table system dspStatus dspUsage

Command Parameters
Multiexcerpt
MultiExcerptName DSP Status
Caption
0 Table
1 DSP Status Attributes
3 DSP Status Attributes
Parameter Description
dspStatus dspUsage
<system name> – The
Spacevars
0 product
system name.
The below fields display raw count of DSP resources (i.e. channels) in use on each slot to aid in understanding which slots are loaded and to what extent in case card removal/hot swap is necessary.
slot1ResourcesUtilized
slot2ResourcesUtilized
slot3ResourcesUtilized
slot4ResourcesUtilized
For each DSP codec, a <codec>Total and <codec>Utilization field displays.
The <codec>Total field indicates how many transcoding sessions the system can support for that codec to G.711.
The <codec>Utilization field indicates what percent of those sessions are actually in use.

NOTE: For compressed-to-compressed transcoding, two resources are required, one for each codec.
Additional fields:
amrNbTotal – Total AMR–NB resource capacity on this server.
amrNbUtilization – Percentage utilization of AMR–NB resources on this server.
amrWbTotal – Total AMR–WB resource capacity on this server.
amrWbUtilization – Percentage utilization of AMR–WB resources on this server.
compressionAllocFailures – Running count of resource allocation failures due to resource exhaustion.
compressionAvailable – Actual compression resources currently available in real time. This essentially equates to the total number of G.711 resources after loading.
compressionTotal – Maximum number of compression resources on the server (i.e. before loading, so this number is static). This essentially equates to the total number of G.711 resources before loading (i.e. lightest codec).
compressionUtilization – Percentage of compression resources in use (accounting for various codec weights). This can be calculated using the formula (compressionTotal – compressionAvailable) / compressionTotal.
NOTE: Use this value when determining the extent of DSP module load (regardless of codec type).
ecmTotal – Total T.38 ECM resource capacity on this server.
ecmUtilization – Percentage utilization of T.38 ECM resources on this server.
ecmV34Total – Total T.38 ECM V.34 resource capacity on this server.
ecmV34Utilization – Percentage utilization of T.38 ECM V.34 resources on this server.
efrTotal – Total EFR resource capacity on this server.
efrUtilization – Percentage utilization of EFR resources on this server.
evrc0Total – Total EVRC0 resource capacity on this server.
evrc0Utilization – Percentage utilization of EVRC0 resources on this server.
evrcb0Total – Total EVRCB0 resource capacity on this server.
evrcb0Utilization – Percentage utilization of EVRCB0 resources on this server.
g711SsTotal – Total G711SS (silence suppression) resource capacity on this server.
g711SsUtilization – Percentage utilization of G711SS (silence suppression) resources on this server.
g711Total – Total G711 resource capacity on this server.
g711Utilization – Percentage utilization of G711 resources on this server.
NOTE: The g711Utilization includes g711 channels in use plus channels that are reserved but not activated as part of the call set up process. In this case, ensure to reserve enough resources to account for the worst case codec. For example, in release 4.2.x, a reserved channel is about 4.5 times as expensive as a G.711 channel.
g711V8Total – Total G711 V8 resource capacity on this server.
g711V8Utilization – Percentage utilization of G711 V8 resources on this server.
g722Total – Total G.722 resource capacity on this server.
g722Utilization – Percentage utilization of G.722 resources on this server.
g722V8Total – Total G.722 V8 resource capacity on this server.
g722V8Utilization – Percentage utilization of G.722 V8 resources on this server.
g726Total – Total G726 resource capacity on this server.
g726Utilization – Percentage utilization of G726 resources on this server.
g726V8Total – Total G726 V8 resource capacity on this server.
g726V8Utilization – Percentage utilization of G726 V8 resources on this server.
g729AbTotal – Total G729A+B resource capacity on this server.
g729AbUtilization – Percentage utilization of G729A+B resources on this server.
g729AbV8Total – Total G729A+B V8 resource capacity on this server.
g729AbV8Utilization – Percentage utilization of G729A+B V8 resources on this server.
g7221Total – Total G.722.1 resource capacity on this server.
g7221Utilization – Percentage utilization of G.722.1 resources on this server.
g7221V8Total – Total G.722.1 V8 resource capacity on this server.
g7221V8Utilization – Percentage utilization of G.722.1 V8 resources on this server.
g7231Total – Total G723.1 resource capacity on this server.
g7231Utilization – Percentage utilization of G7231 resources on this server.
g7231V8Total – Total G723.1 V8 resource capacity on this server.
g7231V8Utilization – Percentage utilization of G7231 V8 resources on this server.
ilbcTotal – Total iLBC resource capacity on this server.
ilbcUtilization – Percentage utilization of iLBC resources on this server.
ilbcV8Total – Total iLBC V8 resource capacity on this server.
ilbcV8Utilization – Percentage utilization of iLBC V8 resources on this server.
opusTotal – Total OPUS resource capacity on this server.
opusUtilization – Percentage utilization of OPUS
Multiexcerpt
MultiExcerptName DSP Status
Caption
0 Table
1 DSP Status Attributes
3 DSP Status Attributes
Parameter Description
dspStatus dspUsage
Status of DSP resources.
This statistic command provides the current number of transcoded sessions per DSP2x slot (SBC 5x10) or SPS100 module (SBC 5x00) depending upon the number of modules installed. SBC 5x10 can include up to four DSP modules. SBC 5x00 can be configured for up to three SPS100 modules (Refer to Customer Replaceable Units for details).
The below fields display raw count of DSP resources (i.e. channels) in use on each slot to aid in understanding which slots are loaded and to what extent in case card removal/hot swap is necessary.
slot1ResourcesUtilized
slot2ResourcesUtilized
slot3ResourcesUtilized
slot4ResourcesUtilized
For each DSP codec, a <codec>Total and <codec>Utilization field displays.
The <codec>Total field indicates how many transcoding sessions the system can support for that codec to G.711.
The <codec>Utilization field indicates what percent of those sessions are actually in use.
NOTE: For compressed-to-compressed transcoding, two resources are required, one for each codec.
amrNbTotal – Total AMR–NB resource capacity on this server.
amrNbUtilization – Percentage utilization of AMR–NB resources on this server.
amrWbTotal – Total AMR–WB resource capacity on this server.
amrWbUtilization – Percentage utilization of AMR–WB resources on this server.
compressionAllocFailures – Running count of resource allocation failures due to resource exhaustion.
compressionAvailable – Actual compression resources currently available in real time. This essentially equates to the total number of G.711 resources after loading.
compressionTotal – Maximum number of compression resources on the server (i.e. before loading, so this number is static). This essentially equates to the total number of G.711 resources before loading (i.e. lightest codec).
compressionUtilization – Percentage of compression resources in use (accounting for various codec weights). This can be calculated using the formula (compressionTotal – compressionAvailable) / compressionTotal.
NOTE: Use this value when determining the extent of DSP module load (regardless of codec type).
ecmTotal – Total T.38 ECM resource capacity on this server.
ecmUtilization – Percentage utilization of T.38 ECM resources on this server.
efrTotal – Total EFR resource capacity on this server.
efrUtilization – Percentage utilization of EFR resources on this server.
evrc0Total – Total EVRC0 resource capacity on this server.
evrc0Utilization – Percentage utilization of EVRC0 resources on this server.
evrcb0Total – Total EVRCB0 resource capacity on this server.
evrcb0Utilization – Percentage utilization of EVRCB0 resources on this server.
g711SsTotal – Total G711SS (silence suppression) resource capacity on this server.
g711SsUtilization – Percentage utilization of G711SS (silence suppression) resources on this server.
g711Total – Total G711 resource capacity on this server.
g711Utilization – Percentage utilization of G711 resources on this server.
NOTE: The g711Utilization includes g711 channels in use plus channels that are reserved but not activated as part of the call set up process. In this case, ensure to reserve enough resources to account for the worst case codec. For example, in release 4.2.x, a reserved channel is about 4.5 times as expensive as a G.711 channel.
g722Total – Total G.722 resource capacity on this server.
g722Utilization – Percentage utilization of G.722 resources on this server.
g726Total – Total G726 resource capacity on this server.
g726Utilization – Percentage utilization of G726 resources on this server.
g729AbTotal – Total G729A+B resource capacity on this server.
g729AbUtilization – Percentage utilization of G729A+B resources on this server.
g7221Total – Total G.722.1 resource capacity on this server.
g7221Utilization – Percentage utilization of G.722.1 resources on this server.
g7231Total – Total G723.1 resource capacity on this server.
g7231Utilization – Percentage utilization of G7231 resources on this server.
ilbcTotal – Total iLBC resource capacity on this server.
ilbcUtilization – Percentage utilization of iLBC
resources on this server.
toneAllocFailures – Percentage of tone resource allocation failures on this server.
toneAvailable – Number of tone resources currently unused and available on this server.
toneTotal – Total tone resource capacity on this server.
toneUtilization – Percentage utilization of tone resources on this server.
Ethernet Port
Command Syntax
Code Block
> show table system ethernetPort mgmtAdmin mgmtPortStatus mgmtStatistics packetAdmin packetPortStatus packetStatistics portMonitorStatus portRedundancyGroupStatus

Command Parameters
Multiexcerpt
MultiExcerptName Ethernet Port
Caption
0 Table
1 Ethernet Port Attributes
3 Ethernet Port Attributes
Parameter Description
mgmtAdmin Management ports.
mgmtPortStatus
Management port status details.
ifIndex – The unique ifIndex of this management NIF"
linkState – The state of the interface.
admnDisabled
admnEnabledPortDown
admnEnabledPortUp
nifCreated
nifCreating
null
macAddress – The MAC address of the network interface.
rxDropped – The number of packets dropped due to no receive buffers.
rxErrors – The number of bad packets received
rxPackets – The number of received packets.
txDropped – The number of packets dropped due to no transmit buffers.
txErrors – The number of packet transmit failures.
txPackets – The number of transmitted packets.
mgmtStatistics
Management port transmit and receive statistics.
rxDropped – The number of packets dropped due to no receive buffers.
rxErrors – The number of bad packets received.
rxPackets – The number of received packets.
txDropped – The number of packets dropped due to no transmit buffers.
txErrors – The number of packet transmit failures.
txPackets – The number of transmitted packets.
packetPortStatus
Packet port status details.
allocatedBandwidth – The bandwidth (bytes/second) allocated for a particular port for active media streams.
bandwidthDeviation – The percentage of deviation of actual bandwidth from allocated bandwidth.
bandwidthUsage – The percentage of load (allocatedBandwidth) for a particular port using the formula:
allocatedBandwidth / maxBandwidth * 100
ifIndex – The unique ifIndex of this Packet NIF.
linkState – The state of the interface.
admnDisabled
admnEnabledPortDown
admnEnabledPortUp
null
macAddress – The MAC address of the metwork interface.
maxBandwidth – The maximum bandwidth that the port is capable of supporting. For example,
For SBC 7000 series platform, 95% of 10 GB port is 1,187,500,000 bytes/second.
For SBC 5000 series platform, 95% of 1 GB port is 118,750,000 bytes/second.
negotiatedSpeed – The interface speed.
rxActualBandwidth – The actual Rx bandwidth, which is used for a particular port (bytes/second).
txActualBandwidth – The actual Tx bandwidth, which is used for a particular port (bytes/second).
packetStatistics
Packet port transmit and receive statistics.
rxDropped – The number of packets dropped due to no receive buffers.
rxErrors – The number of bad packets received.
rxPackets – The number of received packets.
txDropped – The number of packets dropped due to no transmit buffers.
txErrors – The number of packet transmit failures.
txPackets – The number of transmitted packets.
portMonitorStatus
The port monitor status.
<ceName> – The SBC server name
failures – Current number failures of this port monitor
faultState – The fault state of the physical port
failed
restored
unknown
linkFailures – The current number of link failures of this port monitor
linkState – The state of the link monitor configured on this port in the link detection group. The linkState is set to “unknown” if link monitors are not configured.
failed
restored
unknown
macAddress – The MAC address associated with the physical port
pmName – The name of this port monitor.
portName – The name of the physical port.
prg – The name of the port redundancy group.
role – The role of the physical port
active
no_role
standby
state – The state of the physical port
down
unknown
up

portRedundancyGroupStatus
Status of the port redundancy group.
<host name> – The server host name.
failureCount – Total number of port monitor failures within this port redundancy group.
failures – The current number of port monitors within this port redundancy group that have declared themselves failed.
ifIndex – The unique ifIndex of this Packet NIF.
ifNum – The unique ifNum of this Packet NIF.
interfaceType – Interface Type of this port redundancy group.
mgmt
pkt
portMonitorCount – The number of port monitors configured in this port redundancy group.
portName – The name of physical/logical port.
primaryMacAddress – The Primary MAC address of the network interface.
secondaryMacAddress – The Secondary MAC address of the network interface.
Anchor
Offenders List Details
Offenders List Details
Offenders List Details
Multiexcerpt
MultiExcerptName Offenders List
Panel
borderColor green
bgColor transparent
borderWidth 2
titleBGColor pink
title IP Policing Offenders Lists
ACL Offenders List – The Access Control List policer offenders list.
Aggregate Offenders List – The aggregate policer offenders list.
ARP Offenders List – The ARP policer offenders list.
Bad Ethernet IP Header Offenders List – The bad Ethernet/IP Header policer offenders list. Ethernet/IP headers are considered bad under the following conditions:
Only broadcast ARP packets are allowed; all other broadcast packets are considered bad.
Anything other than the following unicast/multicast ICMPV6 packets are considered bad.
Type 2 (Packet too big)
Type 3 (ICMP Time exceeded) Code 0 (hop limit exceeded).
Type 128 (ICMPV6 Echo request)
Type 129 (ICMPV6 Echo reply)
Type 135 Neighbor Solicitation
Type 136 Neighbor Advertisement
Anything other than the following unicast ICMPV4 packets are considered bad:
Type 0 Echo Reply
Type 3 Code 4 (Destination unreachable, fragmentation required)
Type 8 Echo Request
Type 11 Code 0 (Time Exceeded, TTL expired)
Only ICMPV6 neighbor discovery packets are allowed under multicast MAC address. Anything else is considered bad.
If DestMAC is zero, it is considered a bad packet.
Anything other than ethertype (IPV4, IPV6, VLAN) is considered bad.
IP Checksum error is considered bad.
IP version other than 4 or 6 is considered bad.
Bad IP Header length
Packet that is not long enough to contain IP header.
TTL == 0 is considered bad.
IPV4 with options set is considered bad.
IPV6 with initial next header field of 0, 60, or 43 is considered bad.
Discard Rule Offenders List – The table of statistics for the discard rule offenders list. For example: ACLi discard rule packets.
IPSec Decrypt Offenders List – The table of statistics for the IPSec Decrypt policer offenders list. For example:
Bad IPSec packet
Authentication error
Invalid SSID
IPSec protocol == AH
Media Offenders List – The table of statistics for the media policer offenders list. For example: Media packets exceeding the policing value.
Rogue Media Offenders List – The table of statistics for the rogue media policer offenders list. For example:
UPD packets received in the media port range, but the destination UDP port is not allocated for media call
Media packets where source port, source address or destination address do not match the allocated media resource
uFlow Offenders List – The table of statistics for the Micro Flow policer offenders list. For example: Microflow packet exceeding the policing rate.
Info
title rogueMediaOffenders List vs. mediaOffendersList
Entries in the Media Offenders List are for allocated media packets that violate the policing rules. The associated call is sending too many media packets. This could indicate a possible “Theft of Service” scenario. Entries in the Rogue Media Offenders List are media packets that the SBC is receiving but no resource is allocated for the packet. This may be a Denial of Service attack or indication that a call was terminated but the other end is still sending media packets.
Anchor
IP-Policing-uFlowStats
IP-Policing-uFlowStats
IP Policing
Multiexcerpt
MultiExcerptName IPPolicing
IP Policing uFlowStats Fields
The following fields display when using
uFlow Index – Index number of this uFlow statistic
Source IP Address – Source IP address
Destination IP Address – Destination IP address
Source IP Port – Source IP port
IP Protocol – IP protocol
LIF Group Id – LIF group ID
Policer Mode – The Policer mode
Policer Bucket Size – Number of packets allowed in the Policer bucket
Policer Credit Rate – Packet fill rate (packets per second)
Agg Policer – The name of the aggregate policer
Agg Policer Priority – Aggregate policer priority level
Packet Accept – The number of packets accepted by the policer
Packet Discard – Number of packets discarded by the policer
Byte Accept – The number of bytes accepted by the policer
Anchor
IP Policing System Current and Interval Attributes
IP Policing System Current and Interval Attributes
IP Policing System Current and Interval
The following table lists systemCurStats and systemIntStats fields. The systemIntStats command results include the following additional attributes:
number – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.
intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
time – The system up time when the interval statisitic is collected for the specified interval.
Info
title Note
Complete IP Policing information related to threshold levels and duration is available at IP Policing Alarm Profile - CLI.
Caption
0 Table
1 IP Policing System Current and Interval Attributes
Attribute Description
aclAcceptPacketCount
The number of accepted packets for the access control list policer.
aclDiscardPacketCount
The number of discarded packets for the access control list policer.
aclMajorAlarmCount
The number of major alarms for the access control list policer.
aclMajorAlarmDuration
The duration of the major alarms in seconds for the access control list policer.
aclMinorAlarmCount
The number of minor alarms for the access control list policer.
aclMinorAlarmDuration
The duration of the minor alarms in seconds for the access control list policer.
aclPeakDiscardRate
The peak discard rate for the access control list policer.
aggregateAcceptPacketCount
The number of accepted packets for the aggregate policer.
aggregateDiscardPacketCount
The number of discarded packets for the aggregate policer.
aggregateMajorAlarmCount
The number of major alarms for the aggregate policer.
aggregateMajorAlarmDuration
The duration of the major alarms in seconds for the aggregate policer.
aggregateMinorAlarmCount
The number of minor alarms for the aggregate policer.
aggregateMinorAlarmDuration
The duration of the minor alarms in seconds for the aggregate policer.
aggregatePeakDiscardRate
The peak discard rate for the aggregate policer.
arpAcceptPacketCount
The number of accepted packets for the ARP policer.
arpDiscardPacketCount
The number of discarded packets for the ARP policer.
arpMajorAlarmCount
The number of major alarms for the ARP policer.
arpMajorAlarmDuration
The duration of the major alarms in seconds for the ARP policer.
arpMinorAlarmCount
The number of minor alarms for the ARP policer.
arpMinorAlarmDuration
The duration of the minor alarms in seconds for the ARP policer.
arpPeakDiscardRate
The peak discard rate for the ARP policer.
badEtherIpHdrDiscardPacketCount
The number of discarded packets for the bad Ethernet/IP Header policer.
badEtherIpHdrMajorAlarmCount
The number of major alarms for the bad Ethernet/IP Header policer.
badEtherIpHdrMajorAlarmDuration
The duration of the major alarms in seconds for the bad Ethernet/IP Header policer.
badEtherIpHdrMinorAlarmCount
The number of minor alarms for the bad Ethernet/IP Header policer.
badEtherIpHdrMinorAlarmDuration
The duration of the minor alarms in seconds for the bad Ethernet/IP Header policer.
badEtherIpHdrPeakDiscardRate
The peak discard rate for the bad Ethernet/IP Header policer.
discardRuleDiscardPacketCount
The number of discarded packets for the discard rule, plus the number of packets that do no match any ACL rule.
discardRuleMajorAlarmCount
The number of major alarms for the discard rule.
discardRuleMajorAlarmDuration
The duration of the major alarms in seconds discard rule.
discardRuleMinorAlarmCount
The number of minor alarms for the discard rule.
discardRuleMinorAlarmDuration
The duration of the minor alarms in seconds for the discard rule.
discardRulePeakDiscardRate
The peak discard rate for the discard rule.
ipSecDecryptAcceptPacketCount
The number of accepted packets for the IPSEC Decrypt policer.
ipSecDecryptDiscardPacketCount
The number of discarded packets for the IPSEC Decrypt policer.
ipSecDecryptMajorAlarmCount
The number of major alarms for the IPSEC Decrypt policer.
ipSecDecryptMajorAlarmDuration
The duration of the major alarms in seconds for the IPSEC Decrypt policer.
ipSecDecryptMinorAlarmCount
The number of minor alarms for the IPSEC Decrypt policer.
ipSecDecryptMinorAlarmDuration
The duration of the minor alarms in seconds for the IPSEC Decrypt policer.
ipSecDecryptPeakDiscardRate
The peak discard rate for the IPSEC Decrypt policer.
mediaAcceptPacketCount
The number of accepted packets for the media policer.
mediaDiscardPacketCount
The number of discarded packets for the media policer.
mediaMajorAlarmCount
The number of major alarms for the media policer.
mediaMajorAlarmDuration
The duration of the major alarms in seconds for the media policer.
mediaMinorAlarmCount
The number of minor alarms for the media policer.
mediaMinorAlarmDuration
The duration of the minor alarms in seconds for the media policer.
mediaPeakDiscardRate
The peak discard rate for the media policer.
rogueMediaDiscardPacketCount
The number of discarded packets for the rogue media policer.
rogueMediaMajorAlarmCount
The number of major alarms for the rogue media policer.
rogueMediaMajorAlarmDuration
The duration of the major alarms in seconds for the rogue media policer.
rogueMediaMinorAlarmCount
The number of minor alarms for the rogue media policer.
rogueMediaMinorAlarmDuration
The duration of the minor alarms in seconds for the rogue media policer.
rogueMediaPeakDiscardRate
The peak discard rate for the rogue media policer.
systemName The SBC system name.
uFlowAcceptPacketCount
The number of accepted packets for the micro flow policer.
uFlowDiscardPacketCount
The number of discarded packets for the micro flow policer.
uFlowMajorAlarmCount
The number of major alarms for the micro flow policer.
uFlowMajorAlarmDuration
The duration of the major alarms in seconds for the micro flow policer.
uFlowMinorAlarmCount
The number of minor alarms for the micro flow policer.
uFlowMinorAlarmDuration
The duration of the minor alarms in seconds for the micro flow policer.
uFlowPeakDiscardRate
The peak discard rate for the micro flow policer.
License
Command Syntax

Code Block
> show table system licenseFeatureStatus licenseInfo licenseLegacyBundleInfo licenseLocalBundleInfo licenseMode licenseRequired licenseServer licenseServerStatus licenseStatus
Command Parameters
Multiexcerpt
MultiExcerptName License
Caption
0 Table
1 License Attributes
3 License Attributes
Parameter Description
licenseFeatureStatus
Status details about each licensed feature.
featureName – The feature name of the registered license
licenseSought – The number of times the SBC requested a license for each feature from the Site License Server (SLS)
licenseNotReceived – The number of times a license is not received from the SLS for each feature
NOTE: This field only applies if the current licenseMode is "network".
licenseInfo
The license status for registered license features.
featureName – The feature name of the registered license
expirationDate – The license expiration date
inUse – The number of licenses used by the SBC for this feature
licenseId – License identifier
source – Source of the license (BuiltIn, Legacy, Local or Network)
usageLimit – The maximum count allowed for this feature
licenseLegacyBundleInfo
License details for the legacy licenses stored on the
Spacevars
0 product
.
bundleName – License bundle name
featureName – The feature name of the registered license
licenseId – License ID
expirationDate – License expiration date
usageLimit – Usage limit for the license
activeLicenseMode – The licensing mode currently in use by the
Spacevars
0 product
licenseLocalBundleInfo
License details for the local licenses stored on the
Spacevars
0 product
.
bundleName – The unique license bundle identifier assigned by this SBC for this license
featureName – The feature name of the registered license
licenseId – The license ID present in the bundle
purchaseOrderId – The bundle purchase order ID
lineId – The purchase order line ID for the bundle
generationDate – The date the license was generated
installDate – The license install date
bundleName – License bundle name
featureName – The feature name of the registered license
licenseId – License ID
expirationDate – License expiration date
usageLimit – Usage limit for the license
fingerPrint1 – The license fingerprint from the standalone node, or one of the HA nodes
fingerPrint2 – The license fingerprint from the second node in an HA configuration
activeLicenseMode – The licensing mode currently in use by the
Spacevars
0 product
licenseLocalBundleInfo
licenseMode
The licensing mode of the License details for the local licenses stored on the
Spacevars
0 product
. application (legacy, local, or network).
(Applies to 'show table' command only)
licenseRequired
Displays the licenseRequired configuration: The configured minimum and maximum number of licenses for a particular feature to request from the Site License Server (SLS) for the SBC application to use.
bundleName – The unique license bundle identifier assigned by this SBC for this license
featureName – The feature name of the registered licenselicenseId
minCount – The license ID present in the bundle
purchaseOrderId – The bundle purchase order ID
lineId – The purchase order line ID for the bundle
generationDate – The date the license was generated
installDate – The license install date
expirationDate – License expiration date
usageLimit – Usage limit for the license
fingerPrint1 – The license fingerprint from the standalone node, or one of the HA nodes
fingerPrint2 – The license fingerprint from the second node in an HA configuration
activeLicenseMode – The licensing mode currently in use by the
Spacevars
0 product
licenseMode
The licensing mode of the
Spacevars
0 product
application (legacy, local, or network).
(Applies to 'show table' command only)
minimum number of licenses the SBC will request from the SLS to retain at the SBC (regardless of demand) when the associated license is first configured.
maxCount – The maximum number of licenses the SBC can request from the SLS.
(Applies to 'show table' command only)
NOTE: This field only applies if the current licenseMode is "network".
NOTE: minCount and maxCount are not allowed for all licenses.
licenseServer
Per-server license configuration.
serverName – The name of the Site License Server (SLS)
priority – The SLS server selection priority
serverAddress – The SLS FQDN or IP address
(Applies to 'show table' command only)
NOTE: This field only applies if the current licenseMode is "network".
licenseServerStatus
License server status details.
serverName – The name of the SLS
isCurrentActive – A result of "y" indicates this server is the last server to respond correctly to a request
requestMessagesSent – The number of license requests sent to this SLS
licenseGrantMessagesReceived – The number of license grant messages received from the SLS
licensePartialGrantMessagesReceived – The number of partial license grant messages received from the SLS
licenseRejectMessagesReceived – Indicates the number of license reject messages received from the SLS
licenseErrors – The number of errors that occurred while sending a request to this SLS (includes no-response received type errors
licenseRequired
Displays the licenseRequired configuration: The configured minimum and maximum number of licenses for a particular feature to request from the Site License Server (SLS) for the SBC application to use.
featureName – The feature name of the registered license
minCount – The minimum number of licenses the SBC will request from the SLS to retain at the SBC (regardless of demand) when the associated license is first configured.
maxCount – The maximum number of licenses the SBC can request from the SLS.
(Applies to 'show table' command only
)
NOTE: This field only applies if the current licenseMode is "network".
NOTE: minCount and maxCount are not allowed for all licenses.
licenseServer
Per-server license configuration.
serverName – The name of the Site License Server (SLS)
priority – The SLS server selection priority
serverAddress – The SLS FQDN or IP address
(Applies to 'show table' command only)
NOTE: This field only applies if the current licenseMode is "network".
licenseServerStatus
License server status details.
serverName – The name of the SLS
isCurrentActive – A result of "y" indicates this server is the last server to respond correctly to a request
requestMessagesSent – The number of license requests sent to this SLS
licenseGrantMessagesReceived – The number of license grant messages received from the SLS
licensePartialGrantMessagesReceived – The number of partial license grant messages received from the SLS
licenseRejectMessagesReceived – Indicates the number of license reject messages received from the SLS
licenseErrors – The number of errors that occurred while sending a request to this SLS (includes no-response received type errors)
NOTE: This field only applies if the current licenseMode is "network".
licenseStatus
The CE license status table describes the current CE license state, for example "dualCe".
cemode

Load Balancing Service
Load Balancing Service (SBC 5xx0/7000/SWe)
licenseStatus
The CE license status table describes the current CE license state, for example "dualCe".
cemode

Load Balancing Service
Load Balancing Service (SBC 5xx0/7000/SWe)
Load Balancing Service status details.
Command Syntax
Code Block
> show table system loadBalancingService groupName inviteRetargetMode leaderStatistics leaderStatus registerRetargetMode resourceInfoStatus
Multiexcerpt
MultiExcerptName LoadBalancingService-5K7K
Command Parameters
Caption
0 Table
1 Load Balancing Service Attributes (SBC 5xx0/7000/SWe)
3 Load Balancing Service Attributes (SBC 5xx0/7000/SWe)
Field Description
groupName Domain name of the load balancing group.
inviteRetargetMode Load balancing service mode for INVITEs.
leaderStatistics
Specifies the leader statistics table.
<key>
leaderElectionAttempts
retransmitCount
requestTimeoutCount
leaderStatus
Displays the IP address of leader nodes in the cluster.
<leader Id>
leaderIPAddress
state
registerRetargetMode Load balancing service mode for REGISTERs.
resourceInfoStatus
Node resource information.
<Id>
callResourceCount
registrationResourceCount
Load Balancing Service (S-SBC)
The following table lists Load Balancing Service status details.
Command Syntax
Code Block
> show table system loadBalancingService dspLeaderStatus dspResourceCacheStatus dspSeedNodeStatus groupName inviteRetargetMode leaderStatistics leaderStatus policerLeaderStatus policerResourceCacheStatus registerRetargetModepolicerSeedNodeStatus resourceInfoStatus
Multiexcerpt
MultiExcerptName LoadBalancingService-5K7K
MultiExcerptName LoadBalancingService-SSBC
Command Parameters
Caption
0 Table
1 Load Balancing Service Attributes (S-SBC)
3 Load Balancing Service Attributes (S-SBC)
Field Description
dspLeaderStatus
Displays the instance status of the leader nodes in the cluster.
<leader Id>
leaderIPAddress
state
dspResourceCacheStatus
Displays media resource cache information.
<node index> – Node ID
nodeIpAddress – Node's IP address
nodePrivateLifGroupName – Node's private LIF group name
nodePrivateLifGroupBandwidth – Available private LIF group bandwidth for this node, in bytes/second
nodePrivateLifGroupTtl – The LIF group Time To Live (TTL) value (Number of seconds remaining for the current resource bandwidth information to be valid) for this node
nodeCodecUnits – Number of available codec units (at any instant) the SSBC can use to allocate the transcoding resources for an active call
nodeCodecCapabilities – Displays the supported codec and corresponding codec units for this node
nodeCodecCapabilitiesExtn – Displays additional supported codec and corresponding codec units than what is listed under nodeCodecCapabilities
nodeCodecTtl – The codec TTL value (Number of seconds the present codec is available) for this node
nodeToneUnits – The percentage of DSP cores available for the present tone
nodeToneTtl – Number of seconds the present tone is available
dspSeedNodeStatus
Displays cluster seed node status.
<Seed ID>
seedNodeIpAddress
Command Parameters
Caption
0 Table
1 Load Balancing Service Attributes (SBC 5xx0/7000/SWe)
3 Load Balancing Service Attributes (SBC 5xx0/7000/SWe)
Description
leaderIPAddress
state
Field
groupName Domain name of the load balancing group.
inviteRetargetMode Load
Specifies the load balancing service mode for INVITEs. Enables load balancing for initial INVITE requests.
If set to redirect, calls may get retargeted using SIP 302 to balance the load.
disabled
redirect
leaderStatistics
Specifies the leader statistics table.
<key>
leaderElectionAttempts
retransmitCount
requestTimeoutCount
leaderStatus
Displays the IP address of leader nodes in the clusternodes in the cluster.
<leader Id>
leaderIPAddress
state
policerLeaderStatus
Displays policer cluster leader node status.
<leader Id>
leaderIPAddress
state
policerResourceCacheStatus
Displays policer media resource cache information.
<node index>
nodeIpAddress
nodeLifGroupName
nodeLifGroupisPrivate
nodeLifGroupBandwidth
nodeLifGroupTtl
policerSeedNodeStatus
Displays policer cluster seed node status.
<leader Id>
registerRetargetMode Load balancing service mode for REGISTERs.
seedNodeIPAddress
resourceInfoStatus
Node resource information.
<Id>
<leader Id>
callResourceCount
registrationResourceCount
Load Balancing Service (
S
M-SBC)
The following table lists Load Balancing Service status details.
Command Syntax
Code Block
> show table system loadBalancingService dspLeaderStatus dspResourceCacheStatus dspSeedNodeStatus groupName inviteRetargetMode leaderStatistics leaderStatus policerLeaderStatus policerResourceCacheStatus policerSeedNodeStatus resourceInfoStatus dspResourceCacheStatus groupName leaderStatistics leaderStatus policerResourceCacheStatus privateIpInterfaceGroupName
Multiexcerpt
MultiExcerptName LoadBalancingService-MSBC
Caption
0 Table
1 Load Balancing Service Attributes (M-SBC)
3 Load Balancing Service Attributes (M-SBC)
Field Description
dspResourceCacheStatus
Displays media resource cache information.
<node index>
nodeIpAddress
nodePrivateLifGroupName
nodePrivateLifGroupBandwidth
nodePrivateLifGroupTtl
nodeCodecUnits
nodeCodecCapabilities
nodeCodecCapabilitiesExtn
nodeCodecTtl
nodeToneUnits
nodeToneTtl
groupName Domain name of the load balancing group.
Multiexcerpt
MultiExcerptName LoadBalancingService-SSBC
Command Parameters
Caption
0 Table
1 Load Balancing Service Attributes (S-SBC)
3 Load Balancing Service Attributes (S-SBC)
Field Description
dspLeaderStatus
Displays the instance status of the leader nodes in the cluster.
<leader Id>
leaderIPAddress
state
dspResourceCacheStatus
Displays media resource cache information.
<node index> – Node ID
nodeIpAddress – Node's IP address
nodePrivateLifGroupName – Node's private LIF group name
nodePrivateLifGroupBandwidth – Available private LIF group bandwidth for this node, in bytes/second
nodePrivateLifGroupTtl – The LIF group Time To Live (TTL) value (Number of seconds remaining for the current resource bandwidth information to be valid) for this node
nodeCodecUnits – Number of available codec units (at any instant) the SSBC can use to allocate the transcoding resources for an active call
nodeCodecCapabilities – Displays the supported codec and corresponding codec units for this node
nodeCodecCapabilitiesExtn – Displays additional supported codec and corresponding codec units than what is listed under nodeCodecCapabilities
nodeCodecTtl – The codec TTL value (Number of seconds the present codec is available) for this node
nodeToneUnits – The percentage of DSP cores available for the present tone
nodeToneTtl – Number of seconds the present tone is available
dspSeedNodeStatus
Displays cluster seed node status.
<Seed ID>
seedNodeIpAddress
groupName Domain name of the load balancing group.
inviteRetargetMode
Specifies the load balancing service mode for INVITEs. Enables load balancing for initial INVITE requests.
If set to redirect, calls may get retargeted using SIP 302 to balance the load.
disabled
redirect
leaderStatistics
Specifies the leader statistics table.
<key>
leaderElectionAttempts
retransmitCount
requestTimeoutCount
leaderStatus
Displays the IP address of leader nodes in the cluster.
<leader Id>
leaderIPAddress
state
policerLeaderStatus
Displays policer cluster leader node status.
<leader Id>
leaderIPAddress
state
policerResourceCacheStatus
Displays policer media resource cache information.
<node index>
nodeIpAddress
nodeLifGroupName
nodeLifGroupisPrivate
nodeLifGroupBandwidth
nodeLifGroupTtl
policerSeedNodeStatus
Displays policer cluster seed node status.
<leader Id>
seedNodeIPAddress
resourceInfoStatus
Node resource information.
<leader Id>
callResourceCount
registrationResourceCount
Load Balancing Service (M-SBC)
Load Balancing Service status details.
Command Syntax
Code Block
> show table system loadBalancingService dspResourceCacheStatus groupName leaderStatistics leaderStatus policerResourceCacheStatus privateIpInterfaceGroupName
Multiexcerpt
MultiExcerptName LoadBalancingService-MSBC
Caption
0 Table
1 Load Balancing Service Attributes (M-SBC)
3 Load Balancing Service Attributes (M-SBC)
Field Description
dspResourceCacheStatus
Displays media resource cache information.
<node index>
nodeIpAddress
nodePrivateLifGroupName
nodePrivateLifGroupBandwidth
nodePrivateLifGroupTtl
nodeCodecUnits
nodeCodecCapabilities
nodeCodecCapabilitiesExtn
nodeCodecTtl
nodeToneUnits
nodeToneTtl
groupName Domain name of the load balancing group.
leaderStatistics
Specifies the leader statistics table.
<key>
leaderElectionAttempts
retransmitCount
requestTimeoutCount
leaderStatus
Displays the IP address of leader nodes in the cluster.
<leader Id>
leaderIPAddress
state
policerResourceCacheStatus
Displays policer media resource cache information.
<node index>
nodeIpAddress
nodeLifGroupName
nodeLifGroupisPrivate
nodeLifGroupBandwidth
nodeLifGroupTtl
privateIpInterfaceGroupName
<name> – The name of the Private IP Interface Group used by M-SBC/T-SBC to communicate with MRF.
Network Processor Statistics
policerResourceCacheStatus
Displays policer media resource cache information.
<node index>
nodeIpAddress
nodeLifGroupName
nodeLifGroupisPrivate
nodeLifGroupBandwidth
nodeLifGroupTtl
privateIpInterfaceGroupName
<name> – The name of the Private IP Interface Group used by M-SBC/T-SBC to communicate with MRF.
Network Processor
Include Page
InternalDebugOnly
InternalDebugOnly
Noprint
Toggle Cloak
Click to expand...
Cloak
Command Syntax
Command Parameters
Network ProcessorINLINETableNetwork Processor Statistics AttributesNetwork Processor Statistics AttributesINLINE
Attribute Description
annStatistics
Announcement statistics:
npId – Network processor ID
numEnable – Current number of announcements enabled
numPlaying – Current number of announcements playing
pktsToDsp – Total number of packets sent to DSP
pktsToEth – Total number of packets sent to Ethernet port
stop – If set, all current announcements will gradually stop
numAnnIndToHost – Number of indications sent
numSlip – Number of announcements with interval slip
outQcongest – Total number of errors
timerAddErr – Number of timer schedule errors
LastErrAid – Last Announcement ID for timerAddErr
indWorkNull – No work entry counter for announcement indication
indBufNull – Buffer null counter for announcement indication
annWorkNull – No work entry counter for announcement
annBufNull – Buffer null counter for announcement
defragStatistics
Packet defragmentation statistics:
npId – Network processor ID
reassembleRequired – Total fragment context created for packets requiring reassembly
goodFragments – Number of good fragments processed
reassembleComplete – Good complete datagram
inUse – Current number of defrag contexts used
errorPkt – Bad fragment packet, duplicate, too many fragments, bad offset, packet too big
timeoutCnt – Number of timeouts that have occurred
badInputBuffer – Bad input buffer
badDefragPool – Invalid buffer pool count
badTimeoutList – Invalid age list for timeout maintenance
tooManyFrags – Number of contexts exceeding maximum fragments allowed
noDefragMatch – Number of fragments failed to find frag context, out of fragment context
digitStatistics
Digit insertion statistics
npId – Network processor ID
startCnt – Total start count
stopCnt – Total stop count
modifyCnt – Total modify count
earlyStartCnt – Total early start (start before end) count
cancelRescheduleCnt – Total cancel and reschedule count
badStopCnt – Total bad stop count
mediaNotEnabledCnt – Total digit commands issued for disabled media flow
uknownStateCnt – total unknown state count
timerCancelFailCnt – Total failure count of cancelling timer bucket
timerAddFailCnt – Total failure count of adding timer bucket
failedGetWork – Unable to get work entry to send digit
failedGetPktBuf – Unable to get packet buffer to send digit
rtcpGenStatistics
RTCP Generation statistics.
npId – Network processor ID
startCnt – Total start count
stopCnt – Total stop count
modifyCnt – Total modify count
haltCnt – Total number of halt commands
restartCnt – Total number of restart commands
cancelCnt – Total cancel and no–schedule count
totalScheduled – Total RTCP packets scheduled
lastScheduled – Last RTCP packet timer scheduled
earlyStartCnt – Total early start (start before end) count
badStopCnt – Total bad stop count
badModifyCnt – Total RTCP modify but RTCP is not enabled count
badGenType – Unsupported gen type passed in command
doubleEnableCnt – Enable command for an already enabled RTCP
timerCancelFailCnt – Total failure count of cancelling timer bucket
timerAddFailCnt – Total failure count of adding timer bucket.
failedGetWork – Unable to get work entry to send RTCP
failedGetPktBuf – Unable to get packet buffer to send RTCP
numWorkAtDiscard – RTCP not generated because state at discard
numWorkAtDisabled – RTCP not generated because state at disabled
numWorkAtHalt – RTCP not generated because state at halt
lastBadRtcpGen – Last RTCP that was not generated

NTP
NTP services management
Command Syntax
Code Block
> show table system networkProcessorStatisticsntp annStatisticskeys defragStatisticspeerStatus digitStatistics rtcpGenStatistics
Command Parameters
Multiexcerpt
MultiExcerptName Network Processor Statistics
Caption
0 Table
1 Network Processor Statistics Attributes
3 Network Processor Statistics Attributes
Attribute Description
annStatistics
Announcement statistics:
npId
numEnable
numPlaying
pktsToDsp
pktsToEth
stop
numAnnIndToHost
numSlip
outQcongest
timerAddErr
LastErrAid
indWorkNull
indBufNull
annWorkNull
annBufNull
defragStatistics
Packet defragmentation statistics:
npId
reassembleRequired
goodFragments
reassembleComplete
inUse
errorPkt
timeoutCnt
badInputBuffer
badDefragPool
badTimeoutList
tooManyFrags
noDefragMatch
digitStatistics
Digit insertion statistics
npId
startCnt
stopCnt
modifyCnt
earlyStartCnt
cancelRescheduleCnt
badStopCnt
mediaNotEnabledCnt
uknownStateCnt
timerCancelFailCnt
timerAddFailCnt
failedGetWork
failedGetPktBuf
rtcpGenStatistics
RTCP Generation statistics.
npId
startCnt
stopCnt
modifyCnt
haltCnt
restartCnt
cancelCnt
totalScheduled
lastScheduled
earlyStartCnt
badStopCnt
badModifyCnt
badGenType
doubleEnableCnt
timerCancelFailCnt
timerAddFailCnt
serverAdmin systemStatus timeZone
Command Parameters
Multiexcerpt
MultiExcerptName NTP
Caption
0 Table
1 NTP Attributes
2 center
3 NTP Attributes
Parameter Description
keys
Displays NTP server key details.
keyId
keyType
keyValue
peerStatus
Displays status information about each NTP peer.
ceName – The name of this SBC server.
ipAddress – IP address of the CE.
state – the state of the NTP peer (insynce, outofsync, reachable).
stratum – A number representing the distance from the reference clock, starting at "0". Stratum 16 represents that a device is out of sync.
refTime – The time this NTP peer was last updated.
serverAdmin
Displays information about each NTP Server configured to provide network time.
ipAddress – The IP address of this NTP server.
version – The NTP version of this NTP server.
minPoll – The minimum poll interval to this NTP server.
maxPoll – The maxiimum poll interval to this NTP server.
state – The configured state of the NTP server entry.
systemStatus
Displays system status information about NTP.
ceName – The name of this SBC server.
clock – The SBC regularly checks system time. This field represents the system time as of the last check by SBC, not the actual system time.
refTime – The time this system was last updated.
timeZone
This table contains Time Zone configuration. Fields include:
name – System name.
zone – The current time zone.
NOTE: In an HA configuration, the Active and Standby system times and refTimes will not match in the results of this command because SBC updates NTP data independently.

Policy Server
Softswitch servers and client services status/statistics details.
Command Syntax
Code Block
> show table system policyServer globalConfig localServer policyServerStatus remoteServer
Command Parameters
Multiexcerpt
MultiExcerptName Policy Server
Caption
0 Table
1 Policy Server Attributes
3 Policy Server Attributes
Attribute Description
globalConfig
Defines global configuration applicable to all policy servers.
congestionControl – The SBC throttles the sending or policy requests to either active or standby PSX when this field is enabled.
mgmtInterfaceGroup – The Management Interface Group to use for communicating with external PSX.
reconnectTimeout – The timer parameter for re-attempting connection to a Policy Server that is in the enabled state in seconds.
switchOverMode – (automatic or manual) This setting determines how the policy server is set to ACTIVE after a switchover.
type – Interface type supported by policyServer.
localServer
Local (embedded) policy server configuration.
action – The action for the operation mode for this trunk group
keepAliveTimer – The time in seconds between sending Keep Alive indications to the internal Policy Server.
mode – Assignment of the Policy Server to have the active, standby, out of service or alternate role.
retries – The maximum number of retransmission attempts for a transaction on this Policy Server.
retryTimer – The time in milliseconds that the SBC waits for a response from the local Policy Server.
state – Administrative state of the softswitch server.
transactionTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after sending it a transaction request.
policyServerStatus
Policy Server status table. Fields include:
allowancePercent – The number of SBC policy requests allowed by PSX. For example, an allowance of 75%, means that the SBC is skipping one out of every four policy requests. This allowance is provisioned on the PSX and enforced on the SBC when PSX Congestion Control is enabled.
averageTransactionTime – Records the average time taken in milliseconds for a softswitch transaction.
congestionLevel – The PSX congestion level.
dataRequests – The cumulative number of data requests received from the softswitch.
index – Identifies the softswitch entry.
interfaceIpAddress – Identifies the IP address the SBC uses to communicate with the PSX for this Policy Server.
ipAddress – IP Address of the softswitch server.
negotiatedVersion – The lowest negotiated protocol version between the gateway and all the active and alternate softswitches.
operState – Operational state of the softswitch.
queriesSkippedAndRejected – The cumulative number of rejected Policy Requests while the active PSX is congested and a standby PSX is either congested or not available.
queriesSkippedAndServiced – The cumulative number of Policy Requests serviced by the standby PSX while the active PSX experienced congestion.
redirectRequests – The cumulative number of redirect requests received from the softswitch.
releaseRequests – The cumulative number of release-call requests received from the softswitch.
serverReconnects – The number of successful reconnections between the gateway and the softswitch.
transactionCompleted – The number of successful transactions between the gateway and the softswitch.
transactionFailedAttempts – The number of unsuccessful transactions between the gateway and the softswitch.
transactionRetryAttempts – The number of transaction retries between the gateway and the softswitch.
version – The negotiated protocol version between the gateway and the softswitch.
remoteServer
Table of softswitch remote server configurations. Fields include:
name – Remote server name.
ipAddress – IP adddress of the remote server.
portNumber – The IP port number of the softswitch server.
state – Administrative state of the softswitch server.
mode – Policy Server mode (active, standby, out of service or alternate role).
action – The method by which queued transactions are processed when oper-state goes to standby or out-of-service. Possibilities include:
dryup – all queue entries are processed to completion unless retries expires.
force – all queue transactions are dropped immediately.
transactionTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after sending it a transaction request.
keepAliveTimer – The time in seconds between sending Keep Alive indications to the Policy Server.
retryTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after retransmitting the transaction request.
retries – The maximum number of retransmission attempts for a transaction on this Policy Server.
subPortNumber – The port number assigned for the IP address of the Policy Server for the specific purpose of communicating subscriber data.

Security
Security management status/statistics details.
Command Syntax
Code Block
> show table system security certExpiryCheck ipsec ocspProfileUses ocspStatistics pki

Command Parameters
Multiexcerpt
MultiExcerptName Security
Caption
0 Table
1 Security Attributes
3 Security Attributes
Parameter Description
certExpiryCheck
Checks for expired certificates, trust anchor validity, and if certificates have been revoked if OSCP is enabled. Fields include:
certReCheckRate – The rate, in hours, to recheck certificates for TLS sessions.
expirationPeriodicWarning – Interval of the periodic warnings in days generated after the certificate has reached the expiry threshold.
expiryWarningThreshold – The number of days before generating a warning for a certificate nearing expiry.

ipsec
IPSec configuration.
ikeDpdInterval – The Dead Peer Detection interval.
ikeRetransmitInterval – The IKE retransmit interval period in seconds.
ikeRetrasmitCount – The number of IKE retransmits.
ocspProfileUses
This table contains OCSP profile usage status. Fields include:
ocspName
tlsName
ocspTlsRefNum
ocspStatistics
This table contains OCSP Statistics. Fields include:
ocspInternalErrors – Number of internal error responses.
ocspMalformedRequests – Number of malformed request responses.
ocspRepondersUnreachable – Number of times OCSP responders are unreachable.
ocspRequestAttempts – Number of OCSP request attempts that have been made.
ocspResponseTimeouts – Number of times OCSP response timeouts are encountered.
ocspResponsesGood – Number of OCSP Responses received with 'Good' status.
ocspResponsesRevoked – Number of OCSP Responses received with 'Revoked' status.
ocspResponsesUnknown – Number of OCSP Responses received with 'Unknown' status.
ocspSigRequired – Number of 'sigRequired' responses.
ocspTryLaters – Number of 'tryLater' responses.
ocspUnauthorized – Number of unauthorized responses.
pki
certStatistics– Certificate statistics.
caCerts – Number of installed CA/remote certificates.
localCerts – Number of installed local certificates.
certificate – Collection of certificates configured on the
Spacevars
0 product
.
encoding – The encoding type of the certificate.
fileName – The certificate content file name
passPhrase – Pass-phrase to decrypt RSA private key in PKCS12 file.
state – The administration state of this certificate.
status – The status of the certificate.
type – The type of the certificate:
remote – certificate is imported from remote location.
local – certificate is used locally.
local-internal – local certificate with private key generated on the
Spacevars
0 product
.

Command Examples
During a switchover call history of only stable calls are maintained. In ‘callCountStatus’ table, all counters except STABLE CALLS are reset to zero when there is a switchover (either force or manual).
To view the call count status for the server before a switchover:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To switch over the management applications and restart “all” the applications:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view
Spacevars
0 product
daughter board status (SBC 7000 results shown):
Noprint
Toggle Cloak
Click to expand...
Cloak
none

Two maintenance fields apply in this view:
IMAGE LOAD FAILURE COUNT – Number of module boot failures since the last successful module boot, for use during diagnostic testing of a potentially failed module.
FPGA VERSION – A card’s programmed firmware version (using FPGA build date).
Info
title Note
The maintenance fields IMAGE LOAD FAILURE COUNT and FPGA VERSION do not apply to SPS100 cards.

To view the synchronization status of the system as a table:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view the front panel LED status of the system:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view fan status (example is for
Spacevars
0 series2
):
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view the license information of the application:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view the MAC addresses status:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view CPU Utilization for the current interval period:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view system congestion status details.
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view system congestion current statistics.
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view DoD mode status.
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view Micro Flow stats:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view LSWU results:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To display the current HA configuration settings:
Noprint
Toggle Cloak
Click to expand...
Cloak

To display results of running verifyDatabaseIntegrity command:
Noprint
Toggle Cloak
Click to expand...
Cloak

To display sync status of active and standby nodes created through a N:1 redundancy group:
Noprint
Toggle Cloak
Click to expand...
Cloak

To view sync status details of the standby node for active nodes created through a N:1 redundancy group configuration.
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view the personality role of the
Spacevars
0 product2
/
Spacevars
0 product3
instance.
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view license bundle details for Legacy licenses:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view license server status details:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

To view license feature status details:
Noprint
Toggle Cloak
Click to expand...
Cloak
none

Pagebreak

Space shortcuts

Page tree

Page History

Versions Compared

Old Version 21

New Version 22

Key

System

Command Syntax

Command Parameters

Admin

Admin

Command Syntax

Command Parameters

Announcements

Command Syntax

Command Parameters

Daughter Board Status

Command Syntax

Command Parameters

AnchorDSP AttributesDSP AttributesDSP

DSP PAD

Command Syntax

Command Parameters

DSP Resources

Command Syntax

Command Parameters

Command Parameters

DSP Resources

Command Syntax

Command Parameters

DSP Status

Command Syntax

Command Parameters

DSP Status

Command Syntax

Command Parameters

Ethernet Port

Command Syntax

Command Parameters

AnchorOffenders List DetailsOffenders List DetailsOffenders List Details

AnchorIP-Policing-uFlowStatsIP-Policing-uFlowStatsIP Policing

IP Policing uFlowStats Fields

AnchorIP Policing System Current and Interval AttributesIP Policing System Current and Interval AttributesIP Policing System Current and Interval

License

Command Syntax

Command Parameters

Load Balancing Service

Load Balancing Service (SBC 5xx0/7000/SWe)

Load Balancing Service

Load Balancing Service (SBC 5xx0/7000/SWe)

Command Syntax

Command Parameters

Load Balancing Service (S-SBC)

Command Syntax

Command Parameters

Command Parameters

Load Balancing Service (

M-SBC)

Command Syntax

Command Parameters

Load Balancing Service (M-SBC)

Command Syntax

Network Processor Statistics

Network Processor

Command Syntax

Command Parameters

NTP

Command Syntax

Command Parameters

Command Parameters

Policy Server

Command Syntax

Command Parameters

Security

Command Syntax

Command Parameters

Command Examples

Anchor
DSP Attributes
DSP Attributes
DSP

Anchor
Offenders List Details
Offenders List Details
Offenders List Details

Anchor
IP-Policing-uFlowStats
IP-Policing-uFlowStats
IP Policing

Anchor
IP Policing System Current and Interval Attributes
IP Policing System Current and Interval Attributes
IP Policing System Current and Interval