...
Caption |
---|
0 | Table |
---|
1 | Intercept Parameters |
---|
3 | Intercept Parameters |
---|
|
|
Parameter | Length/Range | Description |
---|
CallDataChannel
| 1-23 | The user-configurable LI Call Data Control Channel name. (See Call Data Channel Parameters table below for parameter details) |
nodeNumber
| 0-9999999 | The unique global node number to assign to the which is used by the LI server for identification purposes. |
Call Data Channel (CDC) Parameters
...
Caption |
---|
0 | Table |
---|
1 | Call Data Channel Parameters |
---|
3 | Call Data Channel Parameters |
---|
|
|
Parameter | Length/Range | Description |
---|
TCPMediaTransport | N/A | Specifies the media details of LI Server using TCP mode of transport. tcpMediaIpAddress <ip address> – The LI Server's TCP media IP address where the media is sent.tcpMediaPort <port #> – The LI Server's TCP port where the media is sent. (range: 0-65535)
|
UDPMediaTransport | N/A | Specifies the media details of LI Server using UDP mode of transport. udpMediaIpAddress <ip address> – The LI Server's UDP media IP address where the media is sent.udpMediaPort <port #> – The LI Server's UDP port where the media is sent. (range: 0-65535)
|
dsrTcpPort | 0-65535 | <port#> – The LI Server's TCP port where DSR messages are sent. This value is set when mediaTypeIntercepted is set to multimedia . |
interceptStandard
| N/A | The Intercept Standard to use for this Call Data Channel. etsi packetcable (default)threeGpp
|
ipInterfaceGroupName
| 0-23 | <IPIG name> – Name of the IP interface group used to stream to the LI Server.
|
kaTimer
| 0-65535 | <# seconds> (default = 5) – The keep-alive timer value, in seconds.
|
liPolDipForRegdOodMsgs | N/A | Use this flag to control the sending of the policy dip to PSX for registered user's Out-Of-Dialog messages. disabled (default) – SBC does not send policy request to PSX for registered out-of-dialog requests (messages).enabled – SBC sends policy request to PSX for registered out-of-dialog requests for interception.
|
mediationServer | 0-23 | <name> – Name of the Mediation Server. Up to eight Mediation Servers are configurable for each CDC. See Mediation Server Parameters table below for parameter details.
|
mediaTypeIntercepted | N/A | Specifies the type of media interception. default (default) – audio, fax
multimedia – audio, fax, clearmode streams in Encapsulation mode.
Note |
---|
Direct Signaling Report (DSR) messages are also supported. DSR messages are signaling messages generated by SBC, when a call is intercepted. The DSR message contains extra information in the header along with the actual signaling message PDUs. |
|
priIpAddress
| N/A | The primary LI Server's IPv4 address where Call Data Channel messages are sent. (default = 0.0.0.0) |
priMode
| N/A | Mode of the primary server. Options are: active (default)outOfService standby
|
priPort
| 0-65535 | The primary LI Server's UDP port where Call Data Channel messages are sent. (default = 0) |
pristate
| N/A | Use this flag to enable/disable communication to the primary LI Server. enabled (default)disabled
|
retries
| N/A | Number of retries before the LI Call Data Channel is considered as failed. (default = 3) |
rtcpInterception
| N/A | Enable this flag to intercept RTCP information for IMS LI. disabled (default)enabled
|
secIpAddress
| N/A | Secondary LI Server's IPv4 address where Call Data Channel messages are sent. (default = 0.0.0.0) |
secMode
| N/A | Mode of the secondary server. Options are: active outOfService (default) standby
|
secState
| N/A | Use this flag to enable/disable communication to secondary LI Server. enabled (default)disabled
|
vendorId
| N/A | The vendor name of the LI server. none (default)ss8 utimaco verint
|
Mediation Server Parameters
Caption |
---|
0 | Table |
---|
1 | Mediation Server Parameters |
---|
3 | Mediation Server Parameters |
---|
|
|
Parameter | Descriptions |
---|
media
| Mediation server media properties. tcp – Use TCP to transport mediation server details.udp – Use UDP to transport mediation server details.
|
signaling
| Mediation server signaling interception settings. dscpValue – The DSCP value for intercepted signaling/media packets sent on this port. (range: 0-63 / default = 16)ipAddress – The IPv4/IPv6 Address of the mediation server for media/signaling interception over TCP/UDP port.mode – The operational mode of the signaling/media connection towards the mediation server.
inService outOfService (default)
portNumber – The UDP/TCP port number of the mediation server for media/signaling interception. (range: 0-65536 / default = 0)protocolType – The protocol used by the mediation server for signaling interception. This parameter applies to mediation server Signaling properties only.
state – The administrative state of the signaling/media connection towards the mediation server.
disabled (default)enabled
Note |
---|
The protocolType "udp " is not supported for Signaling interception in this release. |
|
Configuring SBC for Different LI Flavors
...
Caption |
---|
0 | Table |
---|
1 | Configuring SBC for Different LI Flavors |
---|
3 | LI Flavors |
---|
|
|
Configuration Settings | LI Flavor |
---|
interceptStandard | vendorId |
---|
packetcable | none/utimaco/verint | Legacy LI (default) |
packetcable | ss8 | SS8 LI |
threeGpp/etsi | none/utimaco/verint | IMS LI |
Command Examples
To configure intercept standard:
...