Warning
Sonus-provided SFP/SFP+ modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Tooltip
tip Use ESD protective device

The 

Spacevars
0 series2

supports the following Small Form-factor Pluggable (SFP/SFP+) transceivers. SFPs (SFP/SFP+) are Customer Replaceable Units (CRU).

The following SFP transceivers are compatible with 

Spacevars
0 series2

Management ports:

Caption
0 Table 1 1Gb SFP Parts
Transceiver Type Product Code Description Copper SBC-SFPCOPPER-1G GIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP) Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES ABCU-5710RZ-SN1   AVAGO TECHNOLOGIES ABCU-5740RZ-SN1   BROADCOM ABCU-5740RZ-SN1   FINISAR FCLF8521P2BTL-SS Single-mode fiber SBC-SFPSM-1G GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 10KM 1310NM, DMI Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFCT-5715PZ-SN1   BROADCOM AFCT-5715PZ-SN1   FINISAR FTLF1318P2BTL-SS   FINISAR FTLF1318P3BTL-SS Multi-mode fiber SBC-5400-SFPMM

-1G

GIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 300M Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFBR-5715PZ-SN1   BROADCOM AFBR-5715PZ-SN1   FINISAR FTLF8519P2BNL-SS   FINISAR FTLF8519P3BNL-SS

The following SFP+ transceivers are compatible

with SBC 7000 series

with 

Spacevars
0 series2

Media and HA ports:

Caption
0 Table 1 10Gb SFP+ Parts
Transceiver Type Product Code Description Single-mode fiber SBC-SFPSM-10G 10.

3GB

3 GB/S, SINGLE MODE, FIBER OPTIC XCVR, LC, SFP, 10KM 1310NM, DM Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFCT-709SMZ-SN1   AVAGO TECHNOLOGIES AFCT-739SMZ-SN1   BROADCOM AFCT-739SMZ-SN1   BROADCOM AFCT-709SMZ-SN1   FINISAR FTLX1471D3BCL-SS Multi-mode fiber SBC-SFPMM-10G 10.

3GB

3 GB/S, MULTIMODE, FIBER OPTIC XCVR, LC, SFP, 300M 850NM, DMI GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFBR-709SMZ-SN1   BROADCOM AFBR-709SMZ-SN1   FINISAR FTLX8574D3BCL-SS   FINISAR FTLX8571D3BCL-SS

Parts and Tools Required

Tooltip
tip ESD protective device

The following items are needed to install/replace a SFP/SFP+ device:

• Electrostatic discharge (ESD) strap
• Replacement SFP/SFP+ transceivers.

Include Page
ESD_wriststrap_7K ESD_wriststrap_7K

Replacing the SFP/SFP+

To replace the SFP/SFP+:

1. Attach an Electrostatic Discharge wrist strap by using the ESD grounding point on the back panel of the chassis. Follow the instructions in the section Connecting Electrostatic Discharge Wrist Strap on SBC 7000.
2. Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Media 0-4) and HA ports (HA 0-1).

3. Disengage the SFP/SFP+ transceiver from

   Spacevars
   0 series2

   . The method used to disengage the SFP/SFP+ transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards.

4. Insert the Sonus-approved SFP/SFP+ transceiver into the desired socket and ensure that the latch mechanism engages.

5. Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
6. Verify LEDs above the part are flashing indicating link status and data activity.

7. Verify port functionality by using the application.

CRU Storage

Tooltip
tip ESD protective device

All 

Spacevars
0 series2

CRUs are shipped in electrostatic discharge bags and should be handled using appropriate ESD precautions.

The storage environment for these CRUs are:

• Humidity must be less than 95% (non-condensing).
• Temperature must be between -40C and +70C.

 

Include Page
ESD_footnote ESD_footnote

Pagebreak