...
Caption |
---|
0 | Figure |
---|
1 | All - System - Admin |
---|
|
Image Modified |
To Edit Admin
...
Caption |
---|
0 | Figure |
---|
1 | All - System - Admin Highlighted |
---|
|
|
The Edit Selected Admin window is displayed below.
Caption |
---|
0 | Figure |
---|
1 | All - System - Admin Edit Window |
---|
|
Image Modified |
The following fields are displayed:
Caption |
---|
0 | Table |
---|
1 | All - System - Admin parameters |
---|
|
Parameter | Description |
---|
Name
| Specifies the name of the SBC system. | Location
| Specifies the physical location of the SBC system. | Contact
| Specifies the contact information of the SBC system. | Local Authentication Enabled
| Specifies the confd CLI user information stored locally can be used for authentication. | External Authentication Enabled
| Specifies the confd CLI user information stored on remote Radius Server used for authentication. | Standby Server State
| Specifies the state of the Stand-by server. It also specifies whether to bring up the Standby server or not. | Util Monitor Stats Interval
| Specifies the time interval for system resource monitoring statistics. The value ranges from 5 to 60 minutes and the default value is 15 minutes. Include Page |
---|
| IntervalStatsMustMatchEMS | IntervalStatsMustMatchEMSNote: If using the EMS in your network, configure EMS PM data collection intervals for the SBC to be both: - Equal to or greater than SBC intervals size, and
- Not less than the SBC interval size multiplied by the SBC number of intervals.
See Insight User Guide for configuration details. Util Monitors Stats Num of Past Interval
| Specifies the number of past intervals saved by the system resource monitoring statistics. | Audit Log State
| Specifies the state of the management audit log. The options are: | Dsp Mismatch Action
| Specifies the action to take for one of the following DSP Mismatch conditions: - Mismatch in DSP card installation across any/all slot locations: Cards must match by slot location. For any mismatched slot, DSP capacity is not used when "
preserveRedundancy " is configured (and card dried up if calls were already in place when the mismatch occurred), or card is left unprotected when "preserveCapacity " is configured. - Mismatch in DSP card type within as lot location: Card installations must match by type – DSP25 (higher capacity) or DSP20 (lower capacity). Same rules as above apply.
The options are: preserveRedundancy (default): The Active automatically triggers a graceful dry-up in an attempt to align DSP hardware capabilities. Once dry-up completes, the Active uses the protected, matching DSP capacity to preserve redundancy.
Note |
---|
Note: During the dry-up period, active calls using the higher Capacity DSPs are not protected in the event that a switchover occurs before the dry up completes. preserveCapacity : The Active continues to use the extra DSP capacity, as needed, assuming appropriate session licenses are in place; partial redundancy is in effect.
Note |
---|
Note: If a switchover occurs, calls using the higher capacity DSPs on Active are not protected during switchover (i.e. partial redundancy). | Cli Set Warning Support
| Specifies whether to enable warning prompts configured for the Set commands or not. The options are: enabled (default) disabled
|
|
...
Caption |
---|
0 | Figure |
---|
1 | All - System - Admin Commands |
---|
|
Image Modified |
The following options are displayed:
Caption |
---|
0 | Table |
---|
1 | Admin Commands parameters |
---|
|
Parameter | Description |
---|
Re Key Confd Encryption Key
| Specifies that it causes encryption keys used by the system configuration database to be regenerated. Note |
---|
Note: Sonus recommends backing up current encrypted parameters in plaintext, if possible. Sonus further recommends performing a full configuration backup immediately after this activity has successfully completed.
| Zeroize Persistent Keys
| Use this control to securely erase all persistent CSPs from the system. The SBC server reboots after confirmation. | Re Generate Ssh RSa Keys
| Specifies that it causes regeneration of all SSH keys. | Restart
| This command restarts a server/CE. | Soft Reset
| Restart the applications on the system without rebooting the server(s). | Switchover
| Perform a switchover of the management applications and restart all applications on currently active server. | Remove Saved Config
| Remove the saved configuration from the system. fileName – Specify filename of configuration to remove from the system.
| Commit Software Upgrade
| Use this control to commit a software upgrade. | Revert Software Upgrade
| Use this control to revert the last live software upgrade using one of the following selectable revert modes: | Identity
| Turn on/off the locator LED of the specified server for the amount of time set with the duration sub-parameter below. duration – The duration (in seconds) to illuminate the locator LED of specified server. The LED illuminates for the specified number of seconds and then extinguishes. A duration of "0" turns off the locator LED and a duration of "255" turns on the locator LED indefinitely. If the duration is not specified, 15 seconds is set as the default value.
|
|