Versions Compared

Old Version 4

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 5

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Note
When configuring LI through EMA/ERE, you must be 'Calea' user. See "Default Accounts and Passwords" for descriptions of users and permissions.

...

Caption
0Table
1Call Data Channel Parameters
3Call Data Channel Parameters

Parameter

Length/Range

Description

TCPMediaTransport N/A

Specifies the media details of LI Server using TCP mode of transport.

  • tcpMediaIpAddress <ip address> – The LI Server's TCP media IP address where the media is sent.
  • tcpMediaPort <port #> – The LI Server's TCP port where the media is sent. (range: 0-65535)
UDPMediaTransport N/A

Specifies the media details of LI Server using UDP mode of transport.

  • udpMediaIpAddress <ip address> – The LI Server's UDP media IP address where the media is sent.
  • udpMediaPort <port #> – The LI Server's UDP port where the media is sent. (range: 0-65535)
dsrTcpPort  0-65535 <port#> – The LI Server's TCP port where DSR messages are sent. This value is set when mediaTypeIntercepted is set to multimedia.

interceptStandard

N/A

The Intercept Standard to use for this Call Data Channel.

  • etsi
  • packetcable (default)
  • threeGpp

ipInterfaceGroupName

0-23

<IPIG name> – Name of the IP interface group used to stream to the LI Server.

kaTimer

0-65535

<# seconds> (default = 5) – The keep-alive timer value, in seconds.

liPolDipForRegdOodMsgs N/A

 Use this flag to control the sending of the policy dip to PSX for registered user's Out-Of-Dialog messages.

  • disabled (default) – SBC does not send policy request to PSX for registered out-of-dialog requests (messages).
  • enabled – SBC sends policy request to PSX for registered out-of-dialog requests for interception.
mediationServer0-23

<name> – Name of the Mediation Server. Up to eight Mediation Servers are configurable for each CDC. See Mediation Server Parameters table below for parameter details.

Note

The mediationServer parameter is only visible when interceptStandard and vendorId are configured for IMS LI (see table Configuring SBC for Different LI Flavors).

mediaTypeIntercepted N/A

Specifies the type of media interception.

  • default (default) – audio, fax

  • multimedia – audio, fax, clearmode streams in Encapsulation mode.

Note

Direct Signaling Report (DSR) messages are also supported. DSR messages are signaling messages generated by SBC, when a call is intercepted. The DSR message contains extra information in the header along with the actual signaling message PDUs.

priIpAddress

N/A

The primary LI Server's IPv4 address where Call Data Channel messages are sent. (default = 0.0.0.0)

priMode

N/A

Mode of the primary server. Options are:

  • active (default)
  • outOfService
  • standby

priPort

0-65535

The primary LI Server's UDP port where Call Data Channel messages are sent. (default = 0)

pristate

N/A

Use this flag to enable/disable communication to the primary LI Server.

  • enabled (default)
  • disabled

retries

N/A

Number of retries before the LI Call Data Channel is considered as failed. (default = 3)

rtcpInterception

N/A

Enable this flag to intercept RTCP information for IMS LI.

  • disabled (default)
  • enabled
Note

The rtcpInterception parameter is only visible when interceptStandard and vendorId are configured as IMS LI (see table Configuring SBC for Different LI Flavors).

secIpAddress

N/A

Secondary LI Server's IPv4 address where Call Data Channel messages are sent. (default = 0.0.0.0)

secMode

N/A

Mode of the secondary server. Options are:

  • active
  • outOfService (default)
  • standby

secState

N/A

Use this flag to enable/disable communication to secondary LI Server.

  • enabled (default)
  • disabled

vendorId

N/A

The vendor name of the LI server.

  • none (default)
  • ss8
  • utimaco
  • verint

...