Page History

...

Include Page

	IP_IGs_ServedBySeperateProcessors
	IP_IGs_ServedBySeperateProcessors

Lawful Intercept Configuration

Command Syntax

As user 'Calea', use the following commands command syntax to configure LI:.

Code Block

language	none

% set addressContext <default> intercept 
   callDataChannel <callDataChannel> 
   nodeNumber <integer>

Command Parameters

The unique global node number to assign to the product

 which is used by the LI server for identification purposes.

Caption

0	Table
1	Intercept Parameters
3	Intercept Parameters

Parameter

Length/Range

Description

CallDataChannel

1-23

The user-configurable LI Call Data Control Channel name.

(See Call Data Channel Parameters table below for parameter details)

nodeNumber

0-9999999

Spacevars

0

Call Data Channel Configuration

As user 'Calea', use the following command to establish the LI call data channel configuration:

Note
The parameter `mediaTypeIntercepted` must be set to "`multimedia`" in order to access `TCPMediaTransport` and `UDPMediaTransport` parameters.

Command Syntax

Code Block

language	none
title	Call Data Channel Syntax

% set addressContext <default> intercept callDataChannel <callDataChannel_name>
	TCPMediaTransport
		tcpMediaIpAddress <tcp media ip address>
		tcpMediaPort <0-65535>
	UDPMediaTransport
		udpMediaIpAddress <udp media ip address>
		udpMediaPort <0-65535>
	dsrTcpPort <0-65535>
	interceptStandard < etsi | packetcable | threeGpp>
	ipInterfaceGroupName <ipInterfaceGroup_Name> 
	mediationServer  (See "Mediation Server Syntax" below)
	kaTimer <kaTimer_name>
	liPolDipForRegdOodMsgs <disabled | enabled>
	mediaTypeIntercepted <default | multimedia>
	priIpAddress <value> 
	priMode <outofservice | standby> 
	priPort <priPort_name> 
	priState <disabled | enabled> 
	retries <value>
	rtcpInterception <disabled | enabled>
	secIpAddress <IP_Address> 
	secMode <active | outofservice | standby> 
	secState <disabled | enabled>
	vendorId <none | ss8 | utimaco | verint>

As user 'Calea', use the following command syntax to configure the Mediation Server.

Code Block

language	none
title	Mediation Server Syntax

% set addressContext <addressContext name> intercept callDataChannel <CDC name> mediationServer <mediationServer name>
	media <tcp | udp>
	signaling
		dscpValue <0-63>
		ipAddress <IPv4/IPv6 address>
		mode <inService | outOfService>
		portNumber <0-65535>
		protocolType <tcp | udp>
		state <disabled | enabled>

As user 'Calea', use the following command in System-level mode to retrieve the LI statistics:

Code Block
> show status addressContext <addressContext name> intercept

Command Parameters

Intercept Parameters

Caption

0	Table
1	Intercept Parameters
3	Intercept Parameters

Parameter

Length/Range

Description

CallDataChannel

1-23

The user-configurable LI Call Data Control Channel name.

(See Call Data Channel Parameters table below for parameter details)

nodeNumber

0-9999999

The unique global node number to assign to the

Spacevars

0	product

which is used by the LI server for identification purposes.

Call Data Channel (CDC) Parameters

Note
The parameter `mediaTypeIntercepted` must be set to "`multimedia`" in order to access `TCPMediaTransport` and `UDPMediaTransport` parameters.

Caption

0	Table
1	Call Data Channel Parameters
3	Call Data Channel Parameters

The parameter mediaTypeIntercepted must be set to "multimedia" to view/configure this parameter.

Parameter

Length/Range

Description

TCPMediaTransport

N/A

Specifies the media details of LI Server using TCP mode of transport.

tcpMediaIpAddress <ip address> – The LI Server's TCP media IP address where the media is sent.
tcpMediaPort <port #> – The LI Server's TCP port where the media is sent. (range: 0-65535)

Note
The parameter `mediaTypeIntercepted` must be set to "`multimedia`" to view/configure this parameter.

UDPMediaTransport

N/A

Specifies the media details of LI Server using UDP mode of transport.

udpMediaIpAddress <ip address> – The LI Server's UDP media IP address where the media is sent.
udpMediaPort <port #> – The LI Server's UDP port where the media is sent. (range: 0-65535)

Note

dsrTcpPort 0-65535 <port#> – The LI Server's TCP port where DSR messages are sent. This value is set when mediaTypeIntercepted is set to multimedia.

interceptStandard

N/A

The Intercept Standard to use for this Call Data Channel.

etsi
packetcable (default)
threeGpp

ipInterfaceGroupName

0-23

<IPIG name> – Name of the IP interface group used to stream to the LI Server.

kaTimer

0-65535

<# seconds> (default = 5) – The keep-alive timer value, in seconds.

liPolDipForRegdOodMsgs

N/A

Use this flag to control the sending of the policy dip to PSX for registered user's Out-Of-Dialog messages.

disabled (default) – SBC does not send policy request to PSX for registered out-of-dialog requests (messages).
enabled – SBC sends policy request to PSX for registered out-of-dialog requests for interception.

mediationServer

10-823

<name> – Name of the Mediation Server. Up to eight Mediation Servers are configurable for each CDC. See Mediation Server Parameters table below for parameter details.

Note
The `mediationServer` parameter is only visible when `interceptStandard` and `vendorId` are configured for IMS LI (see table Configuring SBC for Different LI Flavors).

mediaTypeIntercepted

N/A

Specifies the type of media interception.

default (default) – audio, fax
multimedia – audio, fax, clearmode streams in Encapsulation mode.

Note
Direct Signaling Report (DSR) messages are also supported. DSR messages are signaling messages generated by SBC, when a call is intercepted. The DSR message contains extra information in the header along with the actual signaling message PDUs.

priIpAddress

N/A

The primary LI Server's IPv4 address where Call Data Channel messages are sent. (default = 0.0.0.0)

priMode

N/A

Mode of the primary server. Options are:

active (default)
outOfService
standby

priPort

0-65535

The primary LI Server's UDP port where Call Data Channel messages are sent. (default = 0)

pristate

N/A

Use this flag to enable/disable communication to the primary LI Server.

enabled (default)
disabled

retries

N/A

Number of retries before the LI Call Data Channel is considered as failed. (default = 3)

rtcpInterception

N/A

Enable this flag to intercept RTCP information for IMS LI.

disabled (default)
enabled

Note
The `rtcpInterception` parameter is only visible when `interceptStandard` and `vendorId` are configured as IMS LI (see table Configuring SBC for Different LI Flavors).

secIpAddress

N/A

Secondary LI Server's IPv4 address where Call Data Channel messages are sent. (default = 0.0.0.0)

secMode

N/A

Mode of the secondary server. Options are:

active
outOfService (default)
standby

secState

N/A

Use this flag to enable/disable communication to secondary LI Server.

enabled (default)
disabled

vendorId

N/A

The vendor name of the LI server.

none (default)
ss8
utimaco
verint

Media Server Configuration

Command Syntax

language

Code Block

none

title

Mediation Server

...

% set addressContext <addressContext name> intercept callDataChannel <CDC name> mediationServer <mediationServer name>
	media <tcp | udp>
	signaling
		dscpValue <0-63>
		ipAddress <IPv4/IPv6 address>
		mode <inService | outOfService>
		portNumber <0-65535>
		protocolType <tcp | udp>
		state <disabled | enabled>

...

Parameters

Caption

0	Table
1	Mediation Server Parameters
3	Mediation Server Parameters

Parameter Descriptions

media

Mediation server media properties.

tcp – Use TCP to transport mediation server details.
udp – Use UDP to transport mediation server details.

signaling

Mediation server signaling interception settings.

dscpValue – The DSCP value for intercepted signaling/media packets sent on this port. (range: 0-63 / default = 16)
ipAddress – The IPv4/IPv6 Address of the mediation server for media/signaling interception over TCP/UDP port.
mode – The operational mode of the signaling/media connection towards the mediation server.
- inService
- outOfService (default)
portNumber – The UDP/TCP port number of the mediation server for media/signaling interception. (range: 0-65536 / default = 0)
protocolType – The protocol used by the mediation server for signaling interception. This parameter applies to mediation server Signaling properties only.
- tcp (default)
- udp
state – The administrative state of the signaling/media connection towards the mediation server.
- disabled (default)
- enabled

Note
The `protocolType` "`udp`" is not supported for Signaling interception in this release.

As user 'Calea', use the following command in System-level mode to retrieve the LI statistics:

Code Block

> show status addressContext <addressContext name> intercept

Configuring SBC for Different LI Flavors

...

Space shortcuts

Page tree

Versions Compared

Old Version 3

New Version 4

Key

Lawful Intercept Configuration

Command Syntax

Command Parameters

Call Data Channel Configuration

Command Syntax

Command Parameters

Intercept Parameters

Call Data Channel (CDC) Parameters

Media Server Configuration

Command Syntax

Mediation Server

Parameters

Configuring SBC for Different LI Flavors