Versions Compared

Old Version 6

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 7

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel

In this section:

Table of Contents
maxLevel3
minLevel2

 

The request addressContext zone command is available from both system-level and configure modes. This command allows you to perform system-level commands against a particular zone, such as recovering blacklisted endpoints and resetting statistics counts on all signaling ports.

Command Syntax

Code Block
languagenone
> request addressContext <addressContext name> zone <zone name>
	cacNonRegEndPointRemoveEntry sourceIpAddress <IP address>
	filterSipSrc fqdnEntry <IP address>
	ipPeer <peer name> pathCheck localAdminState state <block | unblock> remoteAdminState state <block | unblock>	
	mtrmConnPort <reset | statReset>
	sipArsEndpointRecoveryAll
	sipArsEndpointRecoveryByIp ipAddress <ip address> port <port#>
	sipSigConnResetAll
	sipSigPortResetAll
	sipTrunkGroup <TG name> packetOutage clear

Command Parameters

 
Caption
0Table
1request addressContext zone Parameters
Hide

Parameter

Description

cacNonRegEndPointRemoveEntry

sourceIpAddress <IP address> – Use this command to remove any CAC entries associated with the specified source IP address

and port

Parameter

Description

.

  • sourceIpAddress <IP address> – The IP address of the IP peer.
  • sourcePort <port> – The port of IP peer.

filterSipSrc 

Use this object to define information related to filtering a SIP message against the source IP address.
ipPeer

<peer name> pathCheck – Use this parameter to manually block or unblock the Local Admin state or Remote Admin state of the peer in the specified zone. 

  • localAdminState state <block | unblock>
  • remoteAdminState state <block | unblock>
mtrmConnPort

Use this object to reset Master Trunk Resource Manager (MTRM) connection port and/or MTRM port statistics.

  • reset – Resets the Master Trunk Group Connection Port and resets all stats related to the connection port.
  • statReset – Resets the Master Trunk Group Connection Port statistics.
Note

NOTE: The reset command has no impact if executed on a disabled or out-of-service object.

sipArsEndpointRecoveryAll

Recovers all blacklisted endpoints in this zone.

Note

NOTE: This command only applies for peers blacklisted using ARS mechanism (not via PATHCHECK).

sipArsEndpointRecoveryByIp

Recovers a blacklisted endpoints in this zone by IP address and port. 

  • ipAddress <ip adddress> – Endpoint's IP address.
  • port <endpoint port#> – Endpoint's port number.
Noteiconfalsetitle

NOTE: This command only applies for peers blacklisted using ARS mechanism (not via PATHCHECK).

sipSigConnResetAllResets all the statistics counts to zero on all SIP signaling port connections.
sipSigPortResetAllResets all the statistics counts to zero on all SIP signaling ports.
sipTrunkGroup

<TG_NAME>  --  Specify the SIP trunk group for which to clear packet outage counts. Options include:

  • cmds queryPsxOnNextRefreshRegister – Use this command in Ingress trunk group (only) to force the SBC to do a PSX dip for the next refresh REGISTER sent to the core. This command is applied to all refresh REGISTERs on all active registrations currently handled by the SBC.
    • newRegistrarIndex – Specify the route index to route to if more than one route is configured.(Default = 0)
    • overRideInternalExpires– Enable flag to override SBX internal expires timer.
      • disable (default)
      • enable
    • registrarFqdn – Refresh REGISTERs on active registrations only towards this FQDN are sent for PSX query.
    • registrarIpAddress – Refresh REGISTERs on active registrations only towards this Registrar IP are sent for PSX query.
  • packetOutage clear
  • services natTraversal adaptiveLearning clearStats
Note

 

queryPsxOnNextRefreshRegister conditions:

  • This feature requires Pathcheck support using OPTIONS Ping and ARS static blacklisting to detect the reachability of a particular IP/FQDN.
  • If both request command and IPSP flags are configured, the request command takes precedence over IPSP flags.
  • The parameters registerFqdn and registerIpAddress are mutually exclusive. Use one or the other in the command, but not both.

 

Example

 

To terminate the CAC for non-registered end point by specifying the IP address and port:The following example clears packet outage counts for SIP trunk group “TG-1” in zone “INTERNAL_ZONE” for address context “default”.

Code Block
languagenone
> request addressContext default zone INTERNAL_ZONE sipTrunkGroup TG-1 packetOutage clear 
reason Trunk Group Packet Outage Detection State is cleared


Pagebreak