Page History

codecEntry

N/A

Specifies the name of an entity consisting of a codec type along with the set of parameters to use with it. Select a default codec name or enter a custom name. Defaults are:

• G711-DEFAULT
• G711SS-DEFAULT
• G723-DEFAULT
• G723A-DEFAULT
• G726-DEFAULT
• G729A-DEFAULT
• G729AB-DEFAULT

codec

N/A

Select a supported codec. (see

 The active code set is applicable to certain AMR narrow-band codecs. Multiple rates may be selected using comma (,). Valid values are:

• AMR-0-4.75kbps
• AMR-1-5.15kbps
• AMR-2-5.90kbps
• AMR-3-6.70kbps
• AMR-4-7.40kbps
• AMR-5-7.950kbps
• AMR-6-10.20kbps
• AMR-7-12.20kbps

codingRate

N/A

Coding rate examples:

dtmf

N/A

Use this parameter to describe how to handle DTMF digits in the media stream.

• relay – Type of DTMF relay. Select any one of the relay:
  • bothOobAnd2833 – Out-of-Band and RFC 2883 are equally received and both can be transmitted. This option would normally be used only in the case where the OOB DTMF signaling is absorbed and not regenerated. For example, the OOB DTMF might go to an application server that needs to detect the DTMF for control purposes but does not process RTP and the 2833 DTMF would go to the destination media address as part of the RTP stream.
  • eitherOobOrRfc2833 – Out-of-Band and RFC 2833 are equally received and only one is transmitted. The one transmitted is the one preferred by the peer or RFC 2833 as the default.
  • none – Leaves the DTMF tones in-band as encoded audio.
  • outOfBand – Carries DTMF in the signaling protocol.
  • rfc2833 – Encodes DTMF into RTP using format and payload type distinct from audio encoding.
• removeDigits – Enables the removal of DTMF digits from the media stream. This applies only if DTMF relay is configured as outOfBand or rfc2833.
  • disable
  • enable (default)

fax

N/A

The treatment taken when the fax tone is detected.

• failureHandling –The behavior when a fax tone is detected but treatment fails for any reason:
  • continue – (default) Continue to process the call.
  • disconnect – Release the call.
• toneTreatment –Treatment taken when the fax tone is detected. Configuration options are:
  • disconnect – Disconnect the call when the fax tone is detected.
  • fallbackToG711 – Fall back to G.711 when the fax tone is detected.
  • fallbackToG711AllowPeerToNegotiateFaxRelay – Upon detecting a fax tone, SBC transitions call to G.711 if current codec is not already G.711. After transiting to G.711, SBC accepts any T.38 reINVITE from the peer.
  • faxRelay – Switch to fax relay (T.38) when the fax tone is detected.
  • faxRelayOrFallbackToG711 – Switch to fax relay (T.38) if supported or fall back to G.711 when fax tone is detected.
  • ignoreDetectionAllowPeerToNegotiateFaxRelay – Accept a T.38 reINVITE (either from a calling party or a called party) and ignore own fax tone detection event..
  • none – (default) Do nothing when the fax tone is detected.
  • notifyPeer – For SIP signaling, notify the peer when the fax tone is detected and let the peer decide the next action.

Sets the level for Forward-Error-Correction (FEC) Redundancy [AMR only].  The default value of "0" means FEC redundancy is disabled.


law

N/A

Specifies the G.711 law to use. Values are::

• ALaw
• ULaw
• deriveFromOtherLeg (default)

Use this parameter to specify the maximum interleave depth value to apply to an endpoint (default = 0).

Enable to force mode change to neighboring modes in active codec set as per RFC4867 (applies to AMR and AMRWB).

• disable (default)
• enable

modem

N/A

Specifies the treatment taken when the modem tone is detected, which can be:

• failureHandling – The behavior when a modem tone is detected but the treatment fails for any reason. The behavior can be:
  • continue (default) – Continue to process the call.
  • disconnect – Release the call.
• toneTreatment – Treatment taken when the modem tone is detected, which can be:

  • applyFaxTreatment – Treat the modem tone as a fax tone, and apply the fax treatment for the selected codec.

• • disconnect – Disconnect the call when the modem tone is detected. 

  • fallbackToG711 – Fall back to G.711 when the modem tone is detected. 

  • none (default) – Do nothing when the modem tone is detected. 

  • notifyPeer – Notify the peer when the modem tone is detected and let the peer decide the next action.

The AMR mode set is applicable to certain AMR wide-band codecs. The possible values are:

• AMR-0-6.6 
• AMR-1-8.85
• AMR-2-12.65
• AMR-3-14.25
• AMR-4-15.85
• AMR-5-18.25
• AMR-6-19.85
• AMR-7-23.05
• AMR-8-23.85

packetSize

N/A

The packet size in milliseconds (ms). Options are based on the type of codec chosen.

amr*, efr, evrc, evrc1, evrc1Fr, evrcb, evrcb1, evrcb1Fr

20, 40, 60

amrwb*

20, 40, 60, 80, 100

bv16, bv32, bv32Fec, dvc-2, g7221-32, g7291, gsm,
Isac, l16-16, msrta8, msrta16, silk8, silk12, silk16,
silk24, speex8, speex8Fec, speex16, speex16Fec, speex32

5, 10, 15, 20, 25, 30, 35,
40, 45, 50, 55, 60, 80, 100

evrc0, evrcb0

20

g711, g711ss

10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60

g722 , g722ss, g726, g726ss

10, 20, 30, 40

g728, g728ss

10, 20, 30, 40, 50, 60, 70, 80,
90, 100, 110, 120, 130, 140, 150

g729a, g729ab, opus

10, 20, 30, 40, 50, 60

g7221, g7221ss

20, 40, 60, 80

g7231, g7231a

30, 60, 90, 120, 150

Ilbc, ilbcss

30, 60

(See Packet Sizes per Codec table below for details)

preferredRtpPayloadType

0-128

Specifies the preferred Real Time Protocol (RTP) payload type to be included in the RTP header of the data packet. Enter a value in the range 0-128. Default is 128.

sendSid

N/A

Enable or disable for sending SIDs.

Enable/disable Silence Suppression mode.

• disable (default)
• enable
  

Use this flag to specify either Constant Bit Rate (CBR) or Variable Bit Rate (VBR) for OPUS codec (default = 0).

• 0 – Variable Bit Rate
• 1 – Constant Bit Rate

useDtx

Set flag to "1" to use Discontinuous Transmission (DTX) For OPUS codec (default = 0).

• 0 – Do not use DTX
• 1 – Use DTX

useFec

Set flag to "1" to use Forward Error Correction (FEC) for OPUS codec (default = 0).

• 0 – Do not use FEC
• 1 – Use FEC