Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1
REV5
REV6
REV3
REV1

Configuring the Call Data Channel

To configure PCSI LI:

Anchor
Configuring SBC Core IPSEC
Configuring SBC Core IPSEC
Configuring SBC Core IPsec

Code Block
### create and configure IKE and IPsec protection profiles
   
set profiles security ipsecProtectionProfile PRGGSX2_IPSEC_PROT_PROF saLifetimeTime 28800
set profiles security ipsecProtectionProfile PRGGSX2_IPSEC_PROT_PROF espAlgorithms inteintegrity hmacSha1,hmacMd5
set profiles security ipsecProtectionProfile PRGGSX2_IPSEC_PROT_PROF espAlgorithms encryption aesCbc128,_3DesCbc
  
set profiles security ikeProtectionProfile PRGGSX2_IKE_PROT_PROF saLifetimeTime 28800
set profiles security ikeProtectionProfile PRGGSX2_IKE_PROT_PROF algorithms encryption aesCbc128,_3DesCbc
set profiles security ikeProtectionProfile PRGGSX2_IKE_PROT_PROF algorithms integintegrity hmacSha1,hmacMd5
set profiles security ikeProtectionProfile PRGGSX2_IKE_PROT_PROF dpdInterval noDpd
commit  

 ###### create IKE peer
  
set addressContext default ipsec peer PRGGSX2 ipAddress 10.220.11.8 preSharedpreSharedKey 00000000000000000000000000000000
set addressContext default ipsec peer PRGGSX2 localIdentity type ipV4Addr ipAddress 10.220.41.161
set addressContext default ipsec peer PRGGSX2 remoteIdentity type ipV4Addr ipAddress 10.220.11.22
set addressContext default ipsec peer PRGGSX2 protocol ikev1 protectionProfile PRGGSX2_IKE_PROT_PROF
commit
  
### create an SPD rule for this IKE peer
  
set addressContext default ipsec spd PRGGSX2_SPD state enabled precedence 1001
set addressContext default ipsec spd PRGGSX2_SPD localIpAddr 10.220.41.161 localIpPrefixLen 32 remoteIpAddr 10.220.11.22 remoteIpPrefixLen 32
set addressContext default ipsec spd PRGGSX2_SPD action protect
set addressContext default ipsec spd PRGGSX2_SPD protocol 170
set addressContext default ipsec spd PRGGSX2_SPD protectionProfile PRGGSX2_IPSEC_PROT_PROF
set addressContext default ipsec spd PRGGSX2_SPD mode transport
set addressContext default ipsec spd PRGGSX2_SPD peer PRGGSX2
commit  

 ###### enable IPsec on the IP interface group
  
set addressContext default ipInterfaceGroup LIG1 enabled
commit

Anchor
Configuring IP Interface Group
Configuring IP Interface Group
Configuring CDC with IP Interface Group

Note

To create CDC, refer to the section Configuring SBC For Lawful Interception.

To configure the IP Interface Group, execute the following command:

Code Block
languagenone
set addressContext default intercept callDataChannel CDC ipInterfaceGroupName LIG1
commit

Anchor
Configuring CDC for Intercept Flavor as PCSI LI
Configuring CDC for Intercept Flavor as PCSI LI
Configuring CDC for Intercept Flavor as PCSI LI

For other options of configuring the intercept flavor as IMS LI, refer to the section Configuring SBC For Lawful Interception.

Code Block
set addressContext default intercept callDataChannel CDC interceptStandard packetCable vendorId ss8
commit

Anchor
Creating a Mediation Server Entry
Creating a Mediation Server Entry
Configuring CDC for Media Interception

Note

The PCSI LI supports configuring up to 8 mediation servers under the CDC.

Code Block
languagenone
set addressContext default intercept callDataChannel CDC interceptStandard mediationServer MS1
commit

Anchor
Configuring Mediation Server for Media Interception over TCP
Configuring Mediation Server for Media Interception over TCP
Configuring CDC for Media Interception over TCP

Code Block
languagenone
set addressContext default intercept callDataChannel CDC mediationServer MS1 media tcp ipAddress fc22:3200::230:7 portNumber 8765 dscpValue 0
commit
set addressContext default intercept callDataChannel CDC mediationServer MS1 media tcp mode inService state enabled
commit

Anchor
Configuring RTCP Interception
Configuring RTCP Interception
Configuring CDC for RTCP Interception

Code Block
set addressContext default intercept callDataChannel CDC rtcpInterception enabled
commit

Viewing PCSI LI Configuration

Enter the show commands to view the configurations.

Anchor
View the Intercept Details
View the Intercept Details
Viewing the Intercept Details

To view the intercept details, execute the following command:

Code Block
> show status addressContext default intercept callDataChannel
callDataChannel CDC {
    mediationServerMediaStatus MS1 {
        tcpChannelstatus inService;
        tcpPacketsSent   0;
        tcpPacketsLost   0;
        udpPacketsSent   0;
        udpPacketsLost   0;
    }
}
[ok]

Anchor
Viewing the CDC Configuration
Viewing the CDC Configuration
Viewing the CDC Configuration

To view the CDC configuration, execute the following command:

Code Block
show addressContext default intercept callDataChannel CDC
interceptStandard    packetcable;
vendorId             ss8;
ipInterfaceGroupName LIG1;
mediationServer MS1 {
    media {
        tcp {
            ipAddress  10.54.6.1;
            portNumber 8765;
            dscpValue  0;
            mode       inService;
            state      enabled;
        }
    }
}
[ok]

Pagebreak