Page History

Panel

In this section:

Table of Contents

maxLevel	2

These sections describe the configuration objects used for signaling. The following diagram depicts a basic signaling configuration.

Caption

0	Figure
1	Call Signaling Configuration Objects

Image Added

Image Removed

Diameter Signaling Controls

Use this object to configure global Diameter signaling controls.

Command Syntax

Code Block

language	none

% set global signaling diamSigControls
	addSonusSpecificAVP <disabled | enabled>
	defaultCCF <ipAddress>
	enableRfApp <disabled | enabled>
	generateFailedEventAcr <disabled | enabled>
	maxACRretransmission <0-3>
	rfInterimAccInrvl <0-180>

Command Parameters

Caption

0	Table
1	Diameter Signaling Control Parameters

Parameter

Length/Range

Description

addSonusSpecificAVP

N/A

Enable flag to send additional CDR information within Sonus vendor-specific Attribute Value Pairs (AVPs) in Accounting-Request (ACR) messages over the existing Rf Interface.

disabled (default)
enabled

InfoSee

NOTE: Refer to Rf Interface Support for AVP details.
`defaultCCF`	Up to 32 characters	`<ip address>` (default = 0.0.0.0) – Specify the IP address to use as the default CCF realm configuration if CCF is not received in the PCFA.
`enableRfApp`	N/A	Use this flag to enable the Rf Accounting application at the system level to send accounting information over Rf Interface. See Rf Interface Support for feature details. `disabled` (default) `enabled`
`generateFailedEventAcr`	N/A	Enable flag to prevent failed call ACR event from being sent. `disabled` (default) `enabled`
`maxACRretransmission`	0-3	Specify the maximum number of ACR retransmissions to use if the SBC does not receive ACA (default = 3).
`rfInterimAccInrvl`	0-180	Use this parameter to specify the interim account interval value to send when no interval is received in ACA. Set value to “0” to not send interim record (default = 30).

Note

NOTE: If ACA has a different value than rfInterimAccInrvl, this parameter is overwritten.

Gateway Signaling Timers

This object allows you to configure the signaling timers for the gateway.

Command Syntax

Code Block

language	none

% set global signaling gwSigTimers
   congRelDelay <delay in seconds>
   establish <timer value, in seconds>
   idle <idle time, in hours>
   keepalive <keepalive time, in seconds>
   retry <number of minutes to attempt to recover GW signaling link>
 
% show global signaling gwSigTimers
 
% delete global signaling gwSigTimers

Command Parameters

Caption

0	Table
1	Global Gateway Signaling Timers Parameters

Parameter	Description
`congRelDelay`	Amount of time (in seconds) that a call which is rejected due to congestion will be delayed before the release is issued. (default = 0).
`establish`	The Gateway Signal Channel Establishment Timer (in seconds.) This value applies to all signal channels. (default = 10).
`idle`	Amount of time (in hours) a GW Signaling Link May be idle before it is taken down. (default = 0).
`keepalive`	The Gateway Signal Channel Keep-alive Timer (in seconds.) This value applies to all signal channels. (default = 3).
`retry`	Amount of time (in minutes) the SBC will continue to attempt to recover a GW Signaling Link as long as there are stable calls up. (default = 60).

H.323 Signaling Timers

This object allows you to configure signaling timers for the node.

Command Syntax

Code Block

language	none

% set global signaling h323SigTimers 
   establish <timer value, in seconds>
   t301 <timer value, in seconds> 
   t302 <timer value, in seconds> 
   t303 <timer value, in seconds> 
   t304 <timer value, in seconds> 
   t310 <T3timer value, in seconds10> 
   tcpConnect <tcpConnect> 

% show global signaling h323SigTimers
 
% delete global signaling h323SigTimers

Command Parameters

Caption

0	Table
1	Global H.323 Signaling Timers Parameters

Parameter	Length/Range	Description
`establish`	0-127	The H225 signal channel establishment timer (in seconds). Default value is 4.
`t301`	0-65535	The T301 call timer (in seconds). Default value is 180 seconds.
`t302`	0-127	The T302 call timer (in seconds). Default value is 15 seconds.
`t303`	0-127	The T303 call timer (in seconds). Default value is 4 seconds.
`t304`	0-127	The T304 call timer (in seconds). Default value is 20 seconds.
`t310`	0-127	The T310 call timer (in seconds). Default value is 10 seconds.
`tcpConnect`	0-127	The TCP connect timer (in seconds). Default value is 3 seconds.

Command Example

To display the global configuration of all h323SigTimers:

Code Block

language	none

% show global signaling h323SigTimers  
   establish 33;  
   tcpConnect 77;  
   t301 444;  
   t302 33;  
   t303 22;  
   t304 33;  
   t310 33;

SIP Peer Overload Control

This object allows you to configure SIP Peer Overload parameters.

Command Syntax

Code Block

language	none

% set global signaling sipPeerOverloadControl 
   discardPeriod <1-10 seconds> 
   rejectThreshold <0-50> 
   samplingPeriod <1-10> 
   stepDownGain <1-200>
% show global signaling sipPeerOverloadControl
  
% delete global signaling sipPeerOverloadControl

Command Parameters

Caption

0	Table
1	Global SIP Peer Overload Control Parameters

Parameter	Length/Range	Description
`discardPeriod`	1-10	Discard period (in seconds) for the Peer Overload back-off algorithm. (default = 2).
`rejectThreshold`	0-50	Specifies the reject threshold (in rejects/sec) for the Peer Overload backoff algorithm. (default = 1).
`samplingPeriod`	1-10	Specifies the sampling period (in seconds) for the Peer Overload back-off algorithm. (default = 2).
`stepDownGain`	1-200	Specifies the step down gain for the Peer Overload back-off algorithm. (default = 100).
`displaylevel`	1-64	To display different levels of output information in show commands.

Command Example

To display the global configuration of all SIP overload control:

Code Block

language	none

% show global signaling sipPeerOverloadControl  
   samplingPeriod 2;  
   discardPeriod 1;  
   stepDownGain 44;  
   rejectThreshold 33;

SIP Signaling Controls

Use this object to configure SIP signaling control parameters.

Command Syntax

Code Block

language	none

% set global signaling sipSigControls 
	egressRNParam <disabled | enabled> 
	loopDetectionFeature <disabled | enabled> 
	maxPduSizeValue <pdusize2kb | pdusize3kb | pdusize6kb | pdusize15kb | pdusize32kb | pdusize60kb> 
	multipleContactsPerAor <disabled | enabled>
	registrarSupportContactParam <disabled | enabled>
    send503DuringSwitchover <disabled | enabled>
	sendDeRegisterContactAsStar <disabled | enabled>
	sendSurrogateUnRegAfterReboot <disabled | enabled>
	suppressErrorInfoHdr <disabled | enabled>
	surrogateRegisterPacingTime <0-10000>
	ucidNodeId <node_id>
 
% show global signaling sipSigControls
 
% delete global signaling sipSigControls

Command Parameters

Caption

0	Table
1	Global SIP Signaling Control Parameters

Parameter

Length/Range

Description

egressRNParam

N/A

The egress RN parameter. Specifies whether the

Spacevars

0	product

sends a Redirecting Number Information Element (RNIE) in the egress leg of the call per RFC3398 when the R-URI and the To header differ.

disabled
enabled (default)

loopDetectionFeature

N/A

When enabled, the SIP Stack performs loop detection on incoming INVITE messages.

disabled – The SIP signaling group processes the INVITE message.
enabled (default)

maxPduSizeValue

N/A

The maximum PDU size recognized by the

Spacevars

0	product

:

pdusize2kb – 2,048 bytes
pdusize3kb – 3,072 bytes
pdusize6kb – 6,000 bytes
pdusize15kb (default) – 15,000 bytes
pdusize32kb – 32,000 bytes
pdusize60kb – 60,000 bytes

multipleContactsPerAor

N/A

Use this flag to support multiple contacts per Address Of Record (AoR).

disabled – Only a single contact per Address of Record is supported.
enabled (default) – The SBC maintains different RCBs for each new registration and verifies the source IP address and port during Registration Control Block (RCB) lookup.

Excerpt Include

	Multiple Contacts per AoR
	Multiple Contacts per AoR
nopanel	true

InfoSee

NOTE: Refer to Multiple Contacts per AoR feature page for additional details.

Note

NOTE: Even though the default value of multipleContactsPerAor is "enabled", during an upgrade the value can be either "enabled" or "disabled".

registrarSupportContactParam

N/A

Enable flag to support parameters in the Contact header:

disabled – Parameters in the Contact header are not supported. This value is provided only for backwards compatibility.
enabled (default) – Parameters in the Contact header are supported.

send503DuringSwitchover

N/A

Use this flag to control the sending of 503 message during a switchover.

disabled – The request is dropped with no 503 messages sent for Invites.
enabled (default) – Send 503 message during a switchover.

Note

NOTE: The Retry-after tag is set to 60 seconds once the 503 message is sent.

sendDeRegisterContactAsStar

N/A

Enable this flag to allow the

Spacevars

0	product

to send the Contact header as a star (*) in DEREGISTER messages if multipleContactsPerAor is disabled.

disabled
enabled (default)

sendSurrogateUnRegAfterReboot

sendSurrogateUnregAFterReboot

N/A

Enable flag to trigger de-register messages to all AORs configured to use the Surrogate Registration feature after a reboot.

disabled (default)
enabled

suppressErrorInfoHdr

N/A

Enable flag to suppress Error-Info header in a response to a request message with syntax error.

disabled (default) – The SBC includes Error-info header in the response.
enabled – The SBC does not include Error-Info header in an error status.

surrogateRegisterPacingTime

0-10000

Use this parameter to specify the time gap, in milliseconds, between a final response of surrogate register and the next surrogate register message sent across all peers. (default = 0, disabled)

If surrogate registration is active and you wish to disable pacing, first disable surrogate registration for each peer using following command syntax:

Code Block

language	none

% set addressContext <AC name> zone <zone name> ipPeer <peer name> surrogateRegistration state disabled

Note

NOTE: Please research the feature to fully understand pacing semantics before using it. This setting is not required in generic deployments. Pacing is applied to all surrogate REGISTER requests generated for all surrogate AoRs.
`ucidNodeId`	1-32767	UCID Node Id used to generate the UCID in the User-to-User Header. (default = 0)

Command Example

To display the global configuration of all SIP signaling control parameters:

Code Block

language	none

% show global signaling sipSigControls
loopDetectionFeature         enabled;
registrarSupportContactParam enabled;
suppressErrorInfoHdr         enabled;
maxPduSizeValue              pdusize3kb;
egressRNParam                enabled;
multipleContactsPerAor       enabled;
surrogateRegisterPacingTime  enabled;
ucidNodeId                   13;
}

Single Radio Voice Call Continuity (SRVCC)

SRVCC provides the ability to transition a voice call from the VoIP/IMS packet domain (LTE) to the legacy circuit domain. Variations of SRVCC are being standardized to support both GSM/UMTS and CDMA 1x circuit domains. For an operator with a legacy cellular network who wishes to deploy IMS/VoIP-based voice services in conjunction with the rollout of an LTE network, SRVCC offers VoIP subscribers with coverage over a much larger area than would typically be available during the roll-out of a new network.

Command Syntax

Code Block

language	none

% set global signaling srvcc
    atcfUri (1-63 chars)
    callLingerTimer (1-32 seconds)
    eStnSr (1-32 chars)
	pstopsSti (0-32 chars)
    stnSr (1-32 chars)

Command Parameters

Caption

0	Table
1	Global SRVCC Parameters
3	Global SRVCC Parameters

Parameter	Length/Range	Description
`atcfUri`	1-63 characters	The SIP URI to be used as the ATCF Path and Management URI.
`callLingerTimer`	1-32 seconds	Number of seconds to wait for INVITE due to STN_SR before clearing the call (default=32).
`eStnSr`	0-32 characters	The Request URI for a emergency transfer call sent by MSC on PS to CS call hand-off. Acceptable characters: alphabetical (upper- and lower-case), numerical (0-9) and any of the following special characters: +,-,.,(,)
`pstopsSti`	0-32 characters	The Request URI for a Packet-Switched-to-Packet-Switched (PS-to-PS) optimized hand-over call. Acceptable characters: alphabetical (upper- and lower-case), numerical (0-9) and any of the following special characters: +,-,.,(,)
`stnSr`	0-32 characters	The Request URI for a transfer call sent by MSC on PS to CS call hand-off. Acceptable characters: alphabetical (upper- and lower-case), numerical (0-9) and any of the following special characters: +,-,.,(,)

Command Example

Code Block
set global signaling srvcc pstopsSti +1-pstopsSti-222 commit show global signaling srvcc pstopsSti pstopsSti +1-pstopsSti-222;

Pagebreak

Space shortcuts

Page tree

Versions Compared

Old Version 8

New Version 9

Key

Diameter Signaling Controls

Command Syntax

Command Parameters

Gateway Signaling Timers

Command Syntax

Command Parameters

H.323 Signaling Timers

Command Syntax

Command Parameters

Command Example

SIP Peer Overload Control

Command Syntax

Command Parameters

Command Example

SIP Signaling Controls

Command Syntax

Command Parameters

Command Example

Single Radio Voice Call Continuity (SRVCC)

Command Syntax

Command Parameters

Command Example