add_docsetworkflow_for_workflowtechpubs |
---|
APPRJID | SYM-21010 |
---|
AUTH1 | |
---|
DEV1JIRAIDAUTHLDEV1 | CHOR-742 |
---|
SVT1REV5 | |
---|
LSVT1REV6 | |
---|
AUTHJIDREV3 | |
---|
SYM-20480REV1 | |
|
...
When delivered from the factory, Ethernet 1 IP is enabled with DHCP by default, and an IPv4 IP address is acquired via a connected DHCP server. This IP address is used for performing Initial Setup on the
. See
Running Initial Setup more information. The default IP address for the logical interface named
Ethernet 2 IP is 192.168.129.2. After initial configuration, you may configure this logical interface using Settings or Tasks tabs in the WebUI.
About Logical Interfaces - SBC SWe Lite
The
supports five system created logical interfaces (known as Administrative IP, Ethernet 1 IP, Ethernet 2 IP, Ethernet 3 IP, and Ethernet 4 IP). In addition to the system created logical interfaces, the Sonus SBC SWe supports user-created VLAN logical sub-interfaces.Administrative IP
The
system supportsa logical interface called the Admin IP (Administrative IP, also known as the Management IP). The primary IP address is a factory-default IP address of 192.168.128.2/24 and it is used for running Initial Setup of the system. Warning |
---|
The Administrative IP interface should only be used for Running Initial Setup and disconnected when not in use (especially to avoid conflicts with your network). This interface cannot be used for VOIP media or protocols. |
Ethernet IP
The
system has four logical interfaces. In most deployments, one of these logical interfaces (typically Ethernet 1 IP) is assigned an IP address used for transporting all the VOIP media packets (e.g., RTP, SRTP) and all protocol packets (e.g., SIP, RTCP, TLS). DNS servers of the customer's network should map the system hostname to this IP address. The hostname or these IP addresses may be used by UC-enabling systems such as SIP-phones, IP-PBX and Microsoft Lync Servers and for accessing the WebUI.In the default software, Ethernet 1 IP is enabled and an IPv4 IP address is acquired via a connected DHCP server. This IP address is used for performing Initial Setup on the
. See Running Initial Setup for more information. The default IP address for the logical interface named Ethernet 2 IP is 192.168.129.2. After initial configuration, you may configure this logical interface using Settings or Tasks tabs in the WebUI.About Logical Interfaces - VLAN interfaces
SBC Edge 1000-2000
As described in the Managing VLANs - SBC Edge 1000-2000 section, each time a VLAN is created, a matching Logical Interface is also automatically created. This Logical Interface allows you to configure an IP address and have IP layer access for this VLAN. The configured IP address can be accessed through any Ethernet port that is associated with the given VLAN. VLAN Logical Interfaces behave the same as any other Logical Interface, and can be used for transporting VOIP media packets (e.g. RTP, SRTP), protocol packets (e.g. SIP, RTCP, TLS), and/or dynamic routing.
Note |
---|
When a VLAN Logical Interface is first created, it will be disabled by default. |
SBC SWe Lite
VLAN sub-interfaces allow the separation of either management traffic between the service provider and the customer, or to keep media traffic from multiple sources separate (that need to exist on the same SWe Lite instance). For example, a service provider could use a VLAN to manage a SWe Lite at a customer premise, while also having a management interface for the customer; the service provider and the customer would be on the same physical network, but have separate logical interfaces.
When a VLAN sub-interface is configured, any IP traffic that uses that sub-interface will be VLAN tagged with the configured value.
VLAN sub-interfaces behave the same as any other Logical Interface, and are used for transporting VOIP media packets (e.g. RTP, SRTP), protocol packets (e.g. SIP, RTCP, TLS), and/or dynamic routing.
Configuration for each VLAN sub-interface is identical to the main interfaces (except the VLAN value is used to specify the interface as a sub-interface).
For configuring VLAN sub-interfaces, refer to Managing VLANs - SBC SWe Lite.
About Logical Interfaces - IPv4 and IPv6 Support
...