...
- In the WebUI, click the Settings tab.
In the left navigation pane, go to Node Interfaces > Ports.
Panel |
---|
|
Caption |
---|
| Image Modified |
|
FXS Long Loop
By using the FXS long loop feature, the maximum length of the local loop supported by SBC1K/2K FXS line cards can be extended to 3000 meter. To accomplish this, you must configure the Long Loop on per FXS line card. The FXS port on this line card supports devices connected using up to 3000 meters long cables.
...
In the WebUI, go to Settings > Node Interfaces > Ports.
The Port Table View window appears.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Port Table View |
---|
3 | Port Table View |
---|
| Image Modified |
|
Select SET FXS Local Loop Type option on the top of the window. The following window appears.
Panel |
---|
|
| windowWindow | 3 | Local Loop Type window |
---|
| Image Modified |
|
Select the FXS long loop for FXS line card in Slot 1 and Slot 3.
Note |
---|
You can select FXS long loop for FXS line card in Slot 1, Slot 3, and Slot 5, based on your requirement. There are two available options: Long Loop and Standard. |
Click OK.
A confirmation window appears. You are prompted to confirm the changes.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Confirmation Window |
---|
3 | Confirmation Window |
---|
| Image Modified |
|
Click OK.
Note |
---|
If you want to discard the changes, click Cancel. |
Once this selection is submitted, all the changes are applied to the FXS Line card in each slot. The The following Port Table View window shows port type for each slot. The Port Type is changed form FXS to FXS Long Loop in slot 1 and slot 3.
Also, the FXS line card in slot 2 and slot 4 are disabled and are unavailable to handle calls. This infers that the upper FXS cards in the system are disabled if long loop is applied.
|
Caption |
---|
0 | Figure |
---|
1 | Port Table View After Applying FXS Long Loop |
---|
3 | Port Table View After Applying FXS Long Loop |
---|
| Image Modified |
|
Viewing Monitor Tab
Info |
---|
To view real-time status, click the Monitor tab in the WebUI. |
The following image shows that the FXS Module 2 and FXS Module 4 are not displayed under Sonus SBC 1000 Main Board.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Monitor View |
---|
3 | Monitor View |
---|
| Image Modified |
|
Viewing Overview Tab
Info |
---|
To view the system overview, in the WebUI, go to System > Overview. |
The following image shows that Telco Module 2 and Telco Module 4 are disabled.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Overview Tab |
---|
3 | Overview Tab |
---|
| Image Modified |
|
Viewing Ports Inventory
Info |
---|
To view your Sonus SBC 1000/2000 System's assets, go to System > Inventory Report tab. |
The following image shows that Telco Module 2 and Telco Module 4 are disabled.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Inventory Report |
---|
3 | Inventory Report |
---|
| Image Modified |
|
Configuring FXS Long Loop on SBC 2000
In the WebUI, go to Settings > Node Interfaces > Ports.
The Port Table View window appears.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Port Table View |
---|
3 | Port Table View |
---|
| Image Modified |
|
Select SET FXS Local Loop Type option on the top of the window. The following window appears.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | FXS Long Loop Type |
---|
3 | FXS Long Loop Type |
---|
| Image Modified |
|
Select the FXS long loop for FXS line card in Slot1 and Slot 2.
Click OK.
A confirmation window appears. You are prompted to confirm the changes
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Confirmation Window |
---|
| Image Modified |
|
Once this selection is submitted, all the changes are applied to the FXS Line card in each slot. The following Port Table View window shows port type for each slot. You can see that the Port Type is changed to FXS Long Loop.
Panel |
---|
|
| after applying After Applying FXS Long Loop |
| Image Modified |
|
Viewing Monitor Tab
Info |
---|
To view real-time status, Click the Monitor tab in the WebUI. |
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Monitor Tab |
---|
3 | Monitor Tab |
---|
| Image Modified |
|
Viewing Overview Tab
Info |
---|
To view the system overview, go to System > Overview. |
The Port Status panelshows that the Port Type is changed to FXS Long Loop.
Panel |
---|
|
Caption |
---|
| Image Modified |
|
Viewing Ports Inventory
Info |
---|
To view your Sonus SBC 1000/2000 System's assets, in the WebUI, go to System > Inventory Report tab. |
The Ports panelshows that the Port Type is changed to FXS Long Loop.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Inventory Report |
---|
3 | Inventory Report |
---|
| Image Modified |
|
Modifying a Port
To modify a Port:
Include Page |
---|
| _Modify_Entry_Icon_Only |
---|
| _Modify_Entry_Icon_Only |
---|
nopanel | true |
---|
|
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Modifying a Port |
---|
3 | Modifying a Port |
---|
| Image Modified |
|
Identification/Status - Field Definitions
...